Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
Thread: Socket Chisel Handle Replacement
-
16th July 2022, 09:35 PM #1GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,271
Socket Chisel Handle Replacement
I've recently been given a couple of socket chisels minus handles, they are generic chisels, around 12mm and 18mm in width.
As I've never really done chisel handle replacements I'm wondering if there is a must have wood, or a nice to have wood, or more likely what I can scrounge wood?
Any timber suggestions would be appreciated.
Mick.
-
16th July 2022 09:35 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
16th July 2022, 09:53 PM #2
Mick, are the chisels going to general use, ie used with a mallet or purely paring?
Paring, any timber and no hoop.Witherby Slick.jpg
General use, you will need a hoop on the end and strong, shock absorbing timber like spotty or Jarrah, like the pic.Ward Socket 31mm Firmer.jpgPat
Work is a necessary evil to be avoided. Mark Twain
-
17th July 2022, 04:04 PM #3GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,271
Pat, thanks for the pictures, I have some spotted gum of which I have just enough to do the job, if not then I have a few pieces of Jarrah, or something like that which will easily be enough.
They are just for general use and I had already decided to run with a hoop on the end to keep everything from being mashed down.
Mick.
-
18th July 2022, 08:40 AM #4GOLD MEMBER
- Join Date
- Oct 2018
- Location
- Dandenong Ranges
- Posts
- 1,892
Hi O. Spotted gum will be fine. I have also used Jarrah and didn't put ferrules on the end. Only used with timber mallets and holding up fine. If I am reading the makers mark right they are good chisels, made from laminated steel.
-
18th July 2022, 11:08 AM #5GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,271
I think the name is Matheson Glasgow, but it is not quite clear.
I never knew chisels like these would have been made from laminated steel, in fact: I didn't know much about laminated steel until I did some online searching after reading about laminated steel in this thread.
Viking swords and such... very interesting indeed.
Mick.
Similar Threads
-
SOLD: Sweetheart Socket Chisel 1 1/4”
By section1 in forum WOODWORK - Tools & MachineryReplies: 3Last Post: 15th October 2021, 09:59 AM -
Local supplier of 4 point t handle socket wrenches?
By MWF FEED in forum METALWORK FORUMReplies: 0Last Post: 19th September 2020, 10:20 AM -
Titan socket chisel handle
By Avery in forum HAND TOOLS - UNPOWEREDReplies: 6Last Post: 17th October 2012, 06:08 PM -
Chisel Handle Replacement
By Stu in Tokyo in forum JAPANESE HAND TOOLSReplies: 3Last Post: 2nd September 2008, 01:53 PM -
Setting handle to A E Berg Socket chisel?
By Waldo in forum JAPANESE HAND TOOLSReplies: 9Last Post: 7th December 2007, 09:38 PM