Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 5 of 5
Thread: Tailstock problem
-
29th April 2016, 04:05 PM #1SENIOR MEMBER
- Join Date
- Oct 2011
- Location
- Langwarrin
- Age
- 43
- Posts
- 952
Tailstock problem
Hey all,
In true murphy fashion, as soon as I get my first commission (yay, just hope my skills measure up) my lathe decides to S%^# itself.
Its a Jet 1220
Whilst tightening the tailstock up, I noticed it sort of 'pulled' a bit too easily. Upon the inspection and figuring out that its more than a simple 'tighten this nut here' sort of problem I thought I would post here to see if there is a solution that is widely accepted, or should I use it as a stepping stone to persuade the lovely wife that its time for an upgrade.
Basically, the thread that holds the washer that tightens to the lathe bed has stripped. Does this mean I will need to find someone to manufacture a new one, or do I need to contact jet (or carbatec) to get a new one sent out or due to it being on the lower end of the lathe market, is it a throw away job?
I have attached photos to explain the issue a little better. The main issue I have is the timing of it - as I mentioned earlier I need it running to finish some pieces. Its never a good time to break down though.
20160429_144713.jpg
20160429_144652.jpg
20160429_144607.jpg
Thanks all
Gabriel"All the gear and no idea"
-
29th April 2016 04:05 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
29th April 2016, 04:27 PM #2
Possible short term solutions to finish your piece.
* use clamps to hold the tail stock in place.
* use a bolt, washer and nut to secure the tail stock.
* visit a friend that has a lathe.
If you are going to hold the tail stock in place by the methods mention above, also consider how much pressure you will put on the tail stock.
I originally had an older Hyco lathe and to secure the tail stock required bolt, washer and nut. If I did not tighten it properly it would move backwards when securing the piece.
-
29th April 2016, 04:32 PM #3
Rough and dirty solution... Find a smaller nyloc nut and cut a new thread to suit. Might get you out of trouble short term?
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
29th April 2016, 06:50 PM #4SENIOR MEMBER
- Join Date
- Oct 2011
- Location
- Langwarrin
- Age
- 43
- Posts
- 952
Thanks Jim and Christos,
I have given the clamping method a crack and it seems to work well, just takes a lot longer to do all the small tasks. It will certainly get me out of trouble until I come up with a permanent solution.
Thanks, you are lifesavers!!
Gab"All the gear and no idea"
-
30th April 2016, 01:33 AM #5SENIOR MEMBER
- Join Date
- Jun 2014
- Location
- Tucson, Arizona, USA
- Posts
- 251
It looks like you have a couple threads left on the bolt. Get another nut to fit, adjust the existing nut until it clamps like it did before, put on the other nut, tighten it and get your commission done. After your done with the commission, take the tail stock apart and take it to a machine shop. Have them turn off the threaded stud, bore a hole and tap it to fit a bolt to fit the clamp. Also have them bore a hole for a set screw as now you will need something to set the bolt at the proper location. Heck, you could do it yourself if you have a drill press. ............... Jerry (in Tucson)
Similar Threads
-
I think it needs a new tailstock
By Burner in forum EBAY, GUMTREE, AMAZON (and other sale sites) Metalwork ONLYReplies: 0Last Post: 31st July 2014, 11:56 PM -
Hercus 9A Tailstock Reassembly Problem
By AntJS in forum THE HERCUS AREAReplies: 5Last Post: 14th January 2013, 10:40 AM -
Self ejecting tailstock problem
By bookend in forum WOODTURNING - GENERALReplies: 16Last Post: 19th October 2012, 02:24 AM -
Tailstock DRO
By Stustoys in forum METALWORK FORUMReplies: 58Last Post: 11th May 2011, 01:15 PM -
Now for the tailstock
By Tiger in forum WOODTURNING - GENERALReplies: 8Last Post: 7th June 2006, 09:50 AM