Thread: Timber for pepper mills.

I guess it depends a lot on your skill level and available timbers, mostly I make the 10" grinders ,I have used a lot of different timbers including camphor laurel ,I always seal the insides with several coats of food safe shellac you need to finish the base at about 60mm dia so look at wood in that size range ,lengths are whatever you want with regard to the length of the centre shaft you purchase ,these are aluminium so are easily cut down if needed. The crush grinders can take pepper salt and almost any dried herbs so very versatile .I like light colored timbers for salt and dark timbers for pepper,but I am pretty traditional hehe. you will need a selection of forstner bits for the mechanisms but that should be no problem . They are fun to make ,may take a bit longer than you expect at first but nothing too difficult if even a penmaker like me can turn them out from time to time enjoy, cheers ~ John

Welcome aboard Bowerbird.

Basically any timber is good for a grinder (including Rosewood and Camphor Laurel), as long as it is sealed to keep the nasties out, plus interesting grain helps.

Crushgrind mechanisms, well all I can say is, they are the best IMHO

Thank you John. I'm not sure why my profile only shows 1 post... perhaps because I haven't posted for ages due to health issues.

Yes, I have a set of CarbaTec forstner bits but haven't bought the Crushgrind mechanisms yet. Ok, I turned more than 12 pens last year and nearly 20 keyrings and turned a few other things, so pepper mills are within my skill range.

Do you always seal the inside regardless of timber type?

Cheers,
BB

Originally Posted by gawdelpus

I guess it depends a lot on your skill level and available timbers, mostly I make the 10" grinders ,I have used a lot of different timbers including camphor laurel ,I always seal the insides with several coats of food safe shellac you need to finish the base at about 60mm dia so look at wood in that size range ,lengths are whatever you want with regard to the length of the centre shaft you purchase ,these are aluminium so are easily cut down if needed. The crush grinders can take pepper salt and almost any dried herbs so very versatile .I like light colored timbers for salt and dark timbers for pepper,but I am pretty traditional hehe. you will need a selection of forstner bits for the mechanisms but that should be no problem . They are fun to make ,may take a bit longer than you expect at first but nothing too difficult if even a penmaker like me can turn them out from time to time enjoy, cheers ~ John

Thanks.

Basically any timber is good for a grinder (including Rosewood and Camphor Laurel), as long as it is sealed to keep the nasties out, plus interesting grain helps.

Crushgrind mechanisms, well all I can say is, they are the best IMHO

with sealing the inside of the grinders is feastwatson proof seal ok to use if not where do you get food grade shellac from who sells it
Thanks Andrew

ditto Andrew's comment

Originally Posted by Fireman sam

with sealing the inside of the grinders is feastwatson proof seal ok to use if not where do you get food grade shellac from who sells it
Thanks Andrew

can't see why not , the sealer should be fine , I actually use feast watson mastertouch french polish (from mitre 10) contains shellac ,seems fine to me ,and convenient as its pre mixed and ready to go anytime . Maybe some of the guys in the finishing section may have a better solution cheers ~ John

Thank you John.

Originally Posted by gawdelpus

can't see why not , the sealer should be fine , I actually use feast watson mastertouch french polish (from mitre 10) contains shellac ,seems fine to me ,and convenient as its pre mixed and ready to go anytime . Maybe some of the guys in the finishing section may have a better solution cheers ~ John

Andrew, I just remembered viewing this site some time ago and just revisited now...

FoodSafe Plus

It says that Food Safe product can be used on salad bowls so maybe it's ok for the inside of pepper mills too? Maybe you can ask them? Failing that they do have Hard Shellac listed as one of their products too and another link to their Distributors.

distribs

Rob Day was selling some Ubeaut stuff, not sure if he still does.

Cheers,
BB

Originally Posted by Fireman sam

with sealing the inside of the grinders is feastwatson proof seal ok to use if not where do you get food grade shellac from who sells it
Thanks Andrew