Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 14 of 14
Thread: Turning turning tool handles
-
21st July 2012, 03:07 PM #1
Turning turning tool handles
Greetings
I want to make some handles for some of my turning tools and I have two questions.
Is Wild Cherry (that is what we call it her on the Central Tablelands) suitable for handles?
I'll try and find my tree ID book and see if it is a native and what it should be called.
If I have a limb in it's off the tree state, of say three to four inches or a bit bigger in diameter . Can I put that between centres and happily turn my handle, seems to me that would be fairly strong, but I'm only a mug amateur.
I wanted to use this timber because I have plenty of it.
ThanksIf you find you have dug yourself a hole, the first thing to do is stop digging.
I just finished child-proofing our house - but they still get inside.
-
21st July 2012 03:07 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
21st July 2012, 03:54 PM #2
The Handles.
Hi ozhunter,
Most woods are always pretty good. Sticks or Branches off the ground always work.
If you are after a design, " Richard Raffan's " Book, " Turning Wood ", there is a Handle in the back pages.
The Book maybe in the Library.
I took the book to O/ Works & blew the picture of the handle up to 13in. or 330mm. on A3, took it home & copied it. I took a Rule of course.
Now, nearly all my Handles are of the Shape, & am very pleased with them all.
I only have, what I regard as a Small Hand, so this Shape Handle, just suits me fine.Regards,
issatree.
Have Lathe, Wood Travel.
-
21st July 2012, 04:05 PM #3
Thanks issatree.
I went and had a look at the timber i have at home and I don't think it will be suitable.
Not enough solid wood and a good few cracks.
Might see what I have out at the farm.
I may just "have" to buy some timber at the toy show next week for my handles.If you find you have dug yourself a hole, the first thing to do is stop digging.
I just finished child-proofing our house - but they still get inside.
-
22nd July 2012, 01:46 AM #4GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
Ozhunter,
If you find a piece 6 - 7 inches in diameter, cut to a bit longer that your finish size and split it in 4 pieces. Split rather than cut as it will split along the grain. If wet, put in the lathe and knock the bark and corners off, and let dry.
Discarded bed posts and table legs make nice handles. I pick them up off the side of the street on trash day. The legs can usually be wrenched off the table, and a head or foot board will usually come apart if a corner is bashed on the street. Some are glued up mystery wood, some solid rock maple.
Look on a tool web site or in a catalog for examples of handles. I have large hands, so I turn down to approximate shape and then grab the handle for a fit while still on the lathe and remove stock until it feels about right.So much timber, so little time.
Paul
-
22nd July 2012, 10:20 AM #5
heaps
If you live out around Bathurst it shouldnt be too hard to find some good local timber. What do the local farmers use for fence posts? Any Tee tree growing locally this stufff makes very good handles.
But at the end of the day just about any hardwood would do and if you get stuck talk to your local nursery.
http://www.greeningaustralia.org.au/...CTL_master.pdf
failing that you can talk to your local or Federal land mob for a tree list
Farm Trees Central West NSW - Windyhill Nursery, Orange & Bathurst NSW.
They have a very extensive list of trees some I recognise many I dont. Buts theres literally dozens in the list that would do. It probably seems like alot of work but at the end of the day. But your going to turn up alot of timber good for turning in general of which you can probably get for free to boot.
The central areas of Australia, the uplands,highlands and table lands produce some spectacular timber, many are highly suited to wood turning.
Turning Trees Into Toothpicks
This will get you goingInspiration exists, but it has to find you working. — Pablo Picasso
-
22nd July 2012, 06:31 PM #6
Thanks for the comments folks.
The posts we put in fences now are galvanisii starpickutus. No disrespect to the previous generations of this area but there is next to no yellow or red box left for fence posts. The live trees are gaurded like first born children by all of us, and the dead standing one almost as much.
I wanted a lighter colour for the handles, so I have been resisting using Rosewood, but I have lots of it, so might try one tonight.
Someone said pine makes decent handles, so I dug round the shed and found a piece of clear pine that was left over from something or other (the stuff you buy from Bunnies) and made this
Still need to refine the shape to one I like (and practice make long sloping cuts.)
I'll keep playing till I find something that works. I like the look of the pine, if the Rosewood proves too big of a head ache I might just use the pine.
CheersIf you find you have dug yourself a hole, the first thing to do is stop digging.
I just finished child-proofing our house - but they still get inside.
-
22nd July 2012, 06:40 PM #7Retro Phrenologist
- Join Date
- Oct 2009
- Location
- Springfield NSW
- Age
- 70
- Posts
- 1,007
Most of the turning tool handles I amusing at the moment are made from offcuts from around the garden - bits of grevillea and callistemon mostly. I think there are a couple from the bluegum that grows on the footpath outside my house. It regularly drops suitable sized branches.
____________________________________________________________
there are only 10 types of people in the world. Those that understand binary arithmetic and those that don't.
-
22nd July 2012, 07:08 PM #8SENIOR MEMBER
- Join Date
- Dec 2011
- Location
- Buderim qld
- Posts
- 842
I have a much used camphor laurel handle. Great use for a weed tree.
-
23rd July 2012, 10:55 AM #9
Well for I use what ever is at hand in the way of hardwood, paying little attention to colour and indeed handle shape. In fact I use the handle shape variation as a means of quick ID of the various tools
Inspiration exists, but it has to find you working. — Pablo Picasso
-
25th July 2012, 11:04 PM #10Senior Member
- Join Date
- Mar 2009
- Location
- Blue Mountains
- Posts
- 175
I used a similar shape to the one you have pictured but a lot longer, probably too long in some peoples opinion but I like to steady the tool against my body.
To help identify my tools when they in their covers (air conditioning pipe insulation) or when the sharp end is buried in shavings I have put a groove in the end of the handle which is the shape of the cutting edge of the tool.
Mm. (escapee from the metalwork forum)
-
25th July 2012, 11:13 PM #11
Mm, how long do you make your handles? Mine above is a bit over 16 inches.
If you find you have dug yourself a hole, the first thing to do is stop digging.
I just finished child-proofing our house - but they still get inside.
-
25th July 2012, 11:40 PM #12Senior Member
- Join Date
- Mar 2009
- Location
- Blue Mountains
- Posts
- 175
Hi, The handles I use on my large tools are 19 inches, I have shorter handles on smaller tools which also helps to identify them.
Because I usually work in metal I made knurled ferrules which help identify my tools from others.
-
26th July 2012, 12:04 AM #13
I like the ferrules. Nice individual touch.
If you find you have dug yourself a hole, the first thing to do is stop digging.
I just finished child-proofing our house - but they still get inside.
-
27th July 2012, 04:11 AM #14Senior Member
- Join Date
- Feb 2010
- Location
- Eugene, OR USA
- Posts
- 322
I think just about any hard wood that is pretty straight grained will work. Pine probably could do in a pinch. Most important it to make sure you have a good ferrule to keep the wood from splitting where the tool enters the wood. That is a fulcrum point. They can range from brass or copper sleeves, brass nuts that are actually threaded on, to the Dave Ellsworth method of strongly wrapping nylon or dacron twine around the ferrule part a couple of times, then chasing it with CA glue. For handle shape, after a number of years, I prefer a straight cylinder.
robo hippy
Similar Threads
-
Earn some extra dollars turning some handles
By bryce247 in forum WOODTURNING - GENERALReplies: 0Last Post: 13th July 2011, 11:42 PM -
Another turning tool
By NeilS in forum WOODTURNING - GENERALReplies: 14Last Post: 2nd October 2010, 12:46 PM -
New turning tool
By Frank&Earnest in forum WOODTURNING - GENERALReplies: 24Last Post: 15th November 2009, 09:59 PM -
New Turning Tool On E-Bay
By stevew in forum WOODTURNING - GENERALReplies: 8Last Post: 1st December 2008, 01:58 PM -
Turning Cutlery Handles
By ianmcdougall in forum WOODTURNING - GENERALReplies: 5Last Post: 26th December 2006, 10:29 PM