Results 1 to 13 of 13
Thread: Turning tool identification
-
20th June 2022, 08:01 PM #1Senior Member
- Join Date
- Dec 2013
- Location
- Blue Mountains NSW
- Posts
- 148
Turning tool identification
Hi everyone ,
I picked up some bits and pieces, chucks, turning tools etc. at a garage sale recently and these turning tools were in the box. After some time googling I have been unable to identify them. There appears to be two sets of tools/ cutters, a handle and tool post/ rest as well as another piece ?
There is not manufactures name on any of the items.
-
20th June 2022 08:01 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
20th June 2022, 08:18 PM #2
It’s a “bowl saver” used for cutting a nested set of bowls from one blank.
Certain parts of it look homemade, I’ve never used one but more experienced turners on here will confirm or deny if it has been custom made.Nothing succeeds like a budgie without a beak.
-
20th June 2022, 08:27 PM #3
-
20th June 2022, 10:09 PM #4
I have one but the tool rest on that one looks different. I have heard that changes have been made to later models. Mine was secondhand about 10 years ago.
Regards
John
-
20th June 2022, 10:16 PM #5
The last "tool" could fit into the banjo and used to hold a drill to bore radial holes in a spindle while still in the lathe. Different inserts are used for different size drills.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
21st June 2022, 10:49 AM #6
It's a deep boring post.
As Powderpost has worked out, it fits in your banjo.
The collar sets the height.
The screw on top allows the sleeve to be insert into a pre-drilled shallow hole in the end of the job then tightened to keep the sleeve in position.
The banjo is then clamped down and the lubricated sleeve becomes the tailstock centre.
The boring bar is then inserted through the sleeve.
The advantage over hollow 'dead' tailstock centres is that the sleeves can have a range of IDs to match different sized boring bars, as Powderpost has also worked out...
I have an older one in a bottom drawer somewhere that I haven't used in a very long time. Typically used in making things like lamp stands or woodwind musical instruments.Stay sharp and stay safe!
Neil
-
21st June 2022, 10:52 AM #7
-
21st June 2022, 09:27 PM #8
-
22nd June 2022, 09:29 AM #9
-
22nd June 2022, 09:37 AM #10
-
22nd June 2022, 06:10 PM #11SENIOR MEMBER
- Join Date
- Oct 2009
- Location
- South Africa
- Posts
- 950
-
22nd June 2022, 08:54 PM #12
-
2nd July 2022, 09:24 AM #13SENIOR MEMBER
- Join Date
- Aug 2020
- Location
- Sunshine Coast
- Posts
- 733
Everyone else has said what they are... Hell of a good score!
I've used the bowl saver in the past and they can be a bit of a wrestling match, but that was on North American woods. Not sure I'd use it on a hard gum or iron bark type of wood... If you were thinking of coring some of that type of wood, loosen the drive belt on the lathe so it slips before you get the tool stuck in your chest.
Similar Threads
-
Tool Identification
By Ando967 in forum HAND TOOLS - UNPOWEREDReplies: 2Last Post: 21st December 2016, 09:42 PM -
Timber Identification - For turning?
By Braxtonatoraxto in forum WOODTURNING - GENERALReplies: 9Last Post: 6th October 2016, 04:34 PM -
Tool identification
By ozhunter in forum HAND TOOLS - UNPOWEREDReplies: 17Last Post: 17th July 2012, 04:55 PM -
Tool Identification?
By Conrad85 in forum HAND TOOLS - POWEREDReplies: 4Last Post: 24th March 2012, 01:07 PM