Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 3 of 3
-
14th June 2020, 09:06 AM #1Novice
- Join Date
- Mar 2011
- Location
- Melbourne
- Posts
- 18
Vicmarc chuck size for Laguna Revo midi
Hi experienced wood turners,
I'm new to wood turning and looking to buy a chuck, so thought I would go with an Aussie-made Vicmarc, but I'm not sure which model. Can you please offer any recommendations the Laguna Revo 12-16 midi lathe?
The Revo 12-16 has an inboard capacity of 300 mm over the bed, so I think the VM100 would be a good fit.
The lathe also has an outboard capacity of 400 mm, so I guess the VM120 be better for outboard as I do hope to turn large bowls etc eventually.
I'm not sure if I should just buy a VM120 to use both inboard and outboard or if it would be best to start with VM100 inboard and buy a VM120 for the outboard side down the track once my skills improve? From a cost perspective I'd prefer to stick with one chuck as the jaws etc are not interchangeable between the two models. My concern is that the larger chuck may be too big for the lathe in terms of weight or maybe not recommended for beginner skills?
Thanks for your advice.
-
14th June 2020 09:06 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
14th June 2020, 06:18 PM #2GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,271
I would suggest the VM100 as the best for starting with. The VM100 has quite an array of jaw sets which are more suited to smaller stuff, think pin jaws, pen blank jaws, long nose jaws and shark jaws, to mention a few available. All of the VM100 jaw sets are cheaper than the VM120 equivalent units.
The VM100 has the possibility of using dovetail jaws up to 144mm, which is quite large. The only downside I can see is if you decide to turn a wet blank at maximum size outboard, that would be reasonably heavy. However you would generally use a faceplate screwed onto the blank to start and my personal experience is that the VM100 with big jaws will hold a wet blank that size. I started out with a VM100, eventually acquiring a VM120 for heavier work, but that took a few years to happen before I was ready to move to a bigger chuck.
I would also suggest you pick up some extra jaw screws. If you are constantly changing jaws, then the jaw screws start to get a bit rounded. I picked up a box of 100 jaw screws from a bolt supply place, cheapest way to do so. Ensure though, that you get the correct type of screws, there is a standard. By reading the stuff on the jaw screws that come with the chuck, you will know exactly which screws to obtain.
Mick.
-
14th June 2020, 06:59 PM #3Novice
- Join Date
- Mar 2011
- Location
- Melbourne
- Posts
- 18
Thanks Mick,
just the kind of experienced info I was hoping for.
Similar Threads
-
Laguna Revo 24-36 Wood Lathe Impressions
By Optimark in forum WOODTURNING - GENERALReplies: 18Last Post: 16th December 2020, 05:29 PM -
Laguna Revo 24/36 Lathe, anyone have one?
By Optimark in forum WOODTURNING - GENERALReplies: 4Last Post: 3rd March 2018, 09:06 AM -
Anyone using a Laguna REVO 18-36?
By Luke Maddux in forum WOODTURNING - GENERALReplies: 27Last Post: 9th June 2016, 09:13 PM