Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 26 of 26
Thread: Where is Woodfast now?
-
22nd October 2020, 06:54 PM #16Senior Member
- Join Date
- Apr 2020
- Location
- Seaford, Vic
- Posts
- 397
I seriously considered the new Woodfast 3040 but in the end plumped for a Stubby.
-
22nd October 2020 06:54 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
23rd October 2020, 10:57 PM #17SENIOR MEMBER
- Join Date
- Oct 2009
- Location
- South Africa
- Posts
- 950
I can’t claim to need such a large lathe, but I do enjoying owning one. Yes, it cost a lot, but I’ve made the decision that of all my hobbies and interests, the one I wish to prioritise is my turning, and I know that I should never need to spend money on a lathe again. It can handle anything I’m brave enough to try (and still has a bit in reserve), and will still be perfectly functional long after I’m not.
The options available to me in South Africa are even more restricted than in Aus, basically Jet, Nova, Laguna and recently Vicmarc are imported. I considered importing one myself, but am glad I didn’t need to do that. I went for the Vicmarc.
-
24th October 2020, 09:17 AM #18
That sort of power is fine as long as you can tame it!
It concerns me somewhat that we do have lathes with the capacity to turn quite large objects with more than sufficient power available to turn them. These large lathes also have a considerable speed range. In inexperienced and untrained hands that can be a very dangerous combination.
A small error such as not dialing down the speed after each turning session, and then checking before commencing a new turning project can present very significant hazards for the unwary.Mobyturns
In An Instant Your Life CanChange Forever
-
24th October 2020, 08:09 PM #19GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,268
I think the speed range of the new large Woodfast lathe is excellent, yes it can be an issue and one should always shut down the lathe and go through a set procedure of what you do. My take on this is to switch everything off, turn both speed dials to zero and ensure the directional switches are both set to forward. Last thing after cleaning up, is to use some dry lubricant on the steel beds and anything else that needs protection.
The real difference with these big motors, like on the Woodfast, is that they are 3 phase. The pure grunt and incredible smoothness of the two lathes I have used with single phase into 3 phase via an inverter, is as addictive as anything.
With regard to lathe speeds, before the COVID-19 thingy really stopped life as we know it, I dropped in to help a mate with his new (to him) Record Power Coronet Herald Midi lathe. Biggest midi lathe I've seen, but that aside, it can do a staggering 3,890 rpm. My friend was amazed at this feature and gleefully cranked up his lathe to maximum speed with a chuck on, I didn't know of any chuck that could be used at those speeds, so I quickly shut things down and we commenced some turning learning. I've since learnt that the Record Power chucks can in fact be run at the terminal velocity of their lathes, impressive and good just from a safety point of view; but you wouldn't want anything to go wrong at very high speeds with stuff in a chuck.
The big Woodfast is capable of 20-3,850 rpm, quite a staggering speed range and with three belt positions and 4 bearings in the headstock, it appears to be built for longevity as well as go.
Speaking of size, that big Woodfast lathe is lighter than I thought, it's only 248Kg
The real nice bit about these kinds of lathes, is the heft inherent in the build, which gives you considerable solidness (is that a word?)
The Tailstock on this lathe seems better than the Laguna I have, with regard to the tool storage on/in the tailstock, that is. The Woodfast has what appears to be a door to keep one from scratching oneself on the stored tools. As such I don't use that feature on my lathe after a few times of ripping some skin and worse, ripping some clothing.
I also like the moveable switch box with a magnetic back, the Rikon version of this lathe shows the coiled lead, which is probably pretty good to go anywhere on the front of the machine.
I still have not been able to see the rear to see if the inverter is sealed from dust ingress, hopefully it is.
Mick.
-
24th October 2020, 08:14 PM #20GOLD MEMBER
- Join Date
- Oct 2004
- Location
- Melbourne, Australia.
- Posts
- 1,268
-
25th October 2020, 01:49 AM #21GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
For those of us not willing or able to buy a new big lathe, older made in AU Woodfasts are a wonderful value. Mine below, for which I paid US $850, 20 inch swing, DC variable speed done in the US by Craft Supplies with the 5 speed pulleys intact. When I first got it home, sitting outside on dirt, I put a big out of balance stump on it, set on the low speed pulleys and low variable speed, and turned it on. The lathe and cabinets gently rocked back & forth until I knocked off the out of balance parts. I have another lathe with 36 inches between centers.
So much timber, so little time.
Paul
-
25th October 2020, 11:00 AM #22
Absolutely!
My old bowl lathe had a 1.8m dia capacity, my old JET 0.9m spindle capacity, plus turning with the bearded one has given me experience with a decent amount of large turnings. Having said that, I still have a healthy fear and respect of the power of the 3040, and other large capacity beasts. Care must always be taken as they can, and will, kill you in a blink of an eyelid.Neil____________________________________________Every day presents an opportunity to learn something new
-
25th October 2020, 11:16 AM #23GOLD MEMBER
- Join Date
- Sep 2008
- Location
- North Carolina, USA
- Posts
- 2,327
My old bowl lathe had a 1.8m dia capacity,So much timber, so little time.
Paul
-
25th October 2020, 11:22 AM #24Senior Member
- Join Date
- Apr 2020
- Location
- Seaford, Vic
- Posts
- 397
-
25th October 2020, 09:54 PM #25
It was home made by someone else. It was for making tables more than bowls, before tables were made with routers. The largest bowl I did was 750mm (finished size) for large boardroom tables (for lawyers/engineers/contractors/Councils/Government Departments etc). Since retiring I haven't had any requests for more bowls that size and tables I now do with a router. The 3040 can do 800mm start size max, so if any client wanted a large bowl, I could still do a 750mm.
Neil____________________________________________Every day presents an opportunity to learn something new
-
28th October 2020, 12:14 PM #26
Paul, depending on your HP, you too can turn quite large pieces outboard with your Woodfast by removing the LH threaded handwheel and attaching a LH threaded faceplate or chuck and using a free standing tool rest. An EVS helps in dialing the speed up slowly to overcome the inertia.
LH threaded faceplates and chuck inserts are not so readily come by now, but they can still be found or made.
Anyway, here is an old yellow turning a big one.
Stay sharp and stay safe!
Neil
Similar Threads
-
Woodfast BL 300
By mick661 in forum WOODTURNING - GENERALReplies: 2Last Post: 7th April 2019, 10:44 PM -
Woodfast 410
By Paul39 in forum WOODTURNING - GENERALReplies: 32Last Post: 7th March 2013, 10:01 PM -
woodfast
By hutch in forum TABLE SAWS & COMBINATIONSReplies: 4Last Post: 9th November 2008, 01:10 PM -
New Woodfast BS-500
By hazard in forum BANDSAWSReplies: 27Last Post: 1st November 2007, 12:10 PM -
woodfast
By Tonyz in forum HAND TOOLS - POWEREDReplies: 0Last Post: 17th August 2005, 09:38 PM