Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
-
30th July 2009, 10:22 AM #1Retired
- Join Date
- Jul 2007
- Location
- Kiewa
- Age
- 64
- Posts
- 1,636
Woodfast MC 908 - Vicmarc chucks OK?
My brother has an MC 908 and doesn't know what thread size is on the head stock. I'm thinking of paying him a visit soon and wonder whether my Vicmarc chucks will fit? The inserts I have are for my VL300, not sure about size there either.
I hope someone can help - I may need to get some inserts so I can use my chucks on his lathe.
-
30th July 2009 10:22 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
30th July 2009, 10:39 AM #2
From memory, Woodfasts are either 1 1/8" x 8tpi or 1 1/4" x 8tpi.
I think the Oz Vicmarc's come @ M30x3.5, although I've heard they're 1 1/4" x 8tpi in the States?
So, if we were yanks there'd be a chance... but I think you're out of luck.
- Andy Mc
-
30th July 2009, 11:05 AM #3
Woodfast.
Hi Jeff,
I have'nt had a lot to do with Woodfast, & it depends on the age of this Lathe.
I also think it maybe 1in. 8tpi, which is Whitworth. Of course you could ask Woodfast themselves, & you might need to know the Serial No. to make it easier. Woodfast, not for me ???.
Go to www.cws.au.com as Jim will more likely know.
Regards,
issatree.
-
30th July 2009, 11:19 AM #4
Woodfast mc908 most likely has 30 x 3.5mm thread. I have two, one is a 1982 model and the second one is a 1993 model, both have 30 x 3.5mm thread.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
30th July 2009, 01:50 PM #5
Some of the early ones were 1"x10tpi and then they changed to M30 x 3.5
Probably M30. but just guessing, get your brother to run some calipers over it.Jim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
-
30th July 2009, 10:30 PM #6China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 4,475
My mc 908 is a 1"X 10 tpi it was manufactured in 1991
-
1st August 2009, 04:53 PM #7
My Woodfasts have all been 30 x 3.5, but as Jim suggests get bro to run a ruler across shaft to confirm.
NeilStay sharp and stay safe!
Neil
Similar Threads
-
Vicmarc or Woodfast
By comgreserv in forum WOODTURNING - GENERALReplies: 6Last Post: 17th October 2008, 09:09 PM -
Vicmarc Chucks 5" or 5 1/2"
By cypher in forum WOODTURNING - GENERALReplies: 2Last Post: 18th November 2006, 12:54 AM -
Chucks
By antman in forum WOODTURNING - GENERALReplies: 9Last Post: 13th February 2004, 10:50 PM -
Chucks
By Woodchuck in forum WOODTURNING - GENERALReplies: 7Last Post: 7th October 2003, 11:14 PM -
Chucks
By DarrylF in forum WOODTURNING - GENERALReplies: 8Last Post: 13th November 2002, 01:50 PM