Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 16 to 21 of 21
Thread: Youtube video
-
29th April 2011, 09:04 AM #16
We had the discussion on not using a Spindle Roughing Gouge on anything but spindle work a few months back
here
I've no interest in having a go at Pop's Shed and I thought it was a very well made video. And I hope another is made in similar vein. ie done naturally.
My real shock came from the presentation showing techniques which you wouldn't teach a beginner.regards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
29th April 2011 09:04 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
29th April 2011, 01:45 PM #17SENIOR MEMBER
- Join Date
- Mar 2011
- Location
- brisbane
- Age
- 52
- Posts
- 579
Thanks SM and everyone else, y'all can can rubber stamp "HELPED" on my forehead, for whatever the thread or source of discussions i've learnt something (or refreshed) today, going to go down and reassess my newbie chisel set, and once i've got my lathe going again my methods as well. I've also got a lot more reading and research and link following to do.
Neal.
-
29th April 2011, 02:24 PM #18
Neal
Get lessons - 'tis the best way IMHO
I'm going to sign up for some remedial when I get my act togetherregards
Nick
veni, vidi, tornavi
Without wood it's just ...
-
29th April 2011, 06:10 PM #19
-
2nd May 2011, 10:04 PM #20Retired
- Join Date
- Jul 2007
- Location
- Kiewa
- Age
- 64
- Posts
- 1,636
I missed the clip before it was removed, so can only think / accept that a spindle roughing gouge was used on bowl work ie cross-grain.
It's funny how this "argument" appears from time to time ie "do whatever works".
I accept none of it. Accidents happen for a reason.
In the case of a SPINDLE ROUGHING GOUGE, you can almost shove the tool into a spindle revolving at high revs and not catch, even on the corner of the tool.
Not so with the same corner presented to a bowl ie cross-grain.
It's damn dangerous!
Funny thing is the local club had Ken Wraight up doing a demonstration some time back. Someone was told / warned / advised not to use said roughing gouge on a bowl......
End result was the gouge went flying out the door of the workshop. "Point taken" was the only response from a suitably chastised pupil.
So there are at least two rules for beginners turning bowls: don't use a skew (other than as a scraper) or a spindle roughing gouge for this kind of turning.
Seems simple to me.
And why not just use a bowl gouge anyway? Made for the task.
-
2nd May 2011, 11:31 PM #21Retired
- Join Date
- May 1999
- Location
- Tooradin,Victoria,Australia
- Age
- 73
- Posts
- 11,918
I was not going to answer this as most know my thoughts on this subject.
I refer you to this thread here: https://www.woodworkforums.com/f8/you...turning-89491/ as Nick has put up the other one.
As a woodturning teacher and tutor it is of paramount importance that techniques be taught that ensure the utmost safety to pupil, teacher and equipment.
Surprisingly, this means using the right tool for the job.
Experimentation comes AFTER you have mastered the basics.
Similar Threads
-
YouTube - Miniatur Wunderland *** official corporate video *** largest model railway
By 741Baus in forum SCALE MODELLINGReplies: 7Last Post: 10th June 2009, 06:42 PM -
YouTube - Woodworking Video - Drill Press Safety!
By Dean in forum WOODWORK - GENERALReplies: 9Last Post: 4th November 2008, 03:51 PM -
thought this was a good video, eccentric goblet video
By Speanwoody in forum WOODTURNING - GENERALReplies: 11Last Post: 11th January 2008, 09:33 PM -
Youtube Video
By Wood Butcher in forum WOODTURNING - GENERALReplies: 18Last Post: 13th May 2007, 05:55 PM -
Kiwi (YouTube.com video)
By Skew ChiDAMN!! in forum WOODIES JOKESReplies: 6Last Post: 10th April 2007, 03:26 PM