Thanks Thanks:  0
Likes Likes:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Page 2 of 2 FirstFirst 12
Results 16 to 19 of 19
  1. #16
    Join Date
    May 2004
    Location
    Pakenham, outer Melb SE suburb, Vic
    Age
    54
    Posts
    4,158

    Default

    If you go with the aforementioned spring loaded swing down jockey wheel, consider getting it mounted inside the draw bar, I have done this with mine, haven't found a disadvantage (yet) and it lets you not worry when jacknifing the trailer either side.

    If you end up going for an 8 x 4, ensure it will fit 2440 x 1220 mm inside, some sheets are still actually 8' x 4', not 2400 x 1200 mm.

    HTH..........cheers..............Sean


    The beatings will continue until morale improves.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Age
    2010
    Posts
    Many





     
  3. #17
    Join Date
    May 2003
    Location
    Kuranda, paradise, North Qld
    Age
    62
    Posts
    5,639

    Default

    After having owned inumerable trailers, some of which were bought 2nd hand and the rest were freebies and having spent a lot of valuable time patching and repairing them my most important consideration would be rust resistance.

    I finally built a trailer from scratch in 2000. All from galvanised stock. All the welds were painted liberally (after wire buffing) with a heavy cold Gal primer.. The floor is a full sheet of hardwood exterior ply which was liberally coated with epoxy on the underside and then glued into place with sikaflex. It gets a floodcoat of decking oil about twice a year. The trailer is still as good as the day I built it. Idecided against a gal steel floor as eventually the gal gets scratched enough for it to rust.

    Mick
    "If you need a machine today and don't buy it,

    tomorrow you will have paid for it and not have it."

    - Henry Ford 1938

  4. #18
    Join Date
    Jan 2005
    Location
    Newcastle/Tamworth
    Posts
    520

    Default

    The point about tyres and wheels is a good one. I overtook 2 semis and the blew a tyre (retread) while carrying a load of tiles. Lucky to get off the road safely. Bent the crap out of the mudguard when it delaminated and the whole trailer wobbles a bit now. Luckily the stud pattern was the same as the car! and luckily I had my socket set on the trailer also since the nuts were a different size than the car spanner.

    Luck everywhere really

    Pulse

  5. #19
    Join Date
    Apr 2002
    Location
    Brisbane
    Posts
    5,773

    Default

    Take a drive on any of our major highways on any weekend you are sure to see a trailer stranded with some sort of wheel/tyre problem.
    cheers
    Any thing with sharp teeth eats meat.
    Most powertools have sharp teeth.
    People are made of meat.
    Abrasives can be just as dangerous as a blade.....and 10 times more painfull.

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Trailer
    By rod1949 in forum TRAILERS & OTHER FABRICATED STUFF
    Replies: 26
    Last Post: 29th September 2009, 02:28 PM
  2. Trailer Storage
    By Sir Stinkalot in forum TRAILERS & OTHER FABRICATED STUFF
    Replies: 16
    Last Post: 8th May 2008, 07:36 AM
  3. Getting a TSC10HB off a trailer
    By NightPanther in forum WOODWORK - GENERAL
    Replies: 22
    Last Post: 29th April 2005, 12:47 AM
  4. trailer lights
    By macklin in forum TRAILERS & OTHER FABRICATED STUFF
    Replies: 7
    Last Post: 1st January 2005, 07:57 PM
  5. EBay 18' Hartley 1/2 Cabin on reg. tilt trailer
    By DavidG in forum BOAT BUILDING / REPAIRING
    Replies: 0
    Last Post: 29th May 2004, 10:12 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •