Thread: How to cut thick glass?

Hi Wongo
Is the glass toughened?
I tryed with toughened stuff once, now way it would cut.
But seeing as how you have already cut it, probably not.
I cut glass for leadlight some times, the cutter I use is a tungten wheeled one with an oil reservouir, not cheap about $60, but it always works.
Maybe you should use some kind of lubricant, such as kero, turps, light oil, etc.
Anyone can cut glass with the right tool, technique.
Hey, if I can do it so can any one else.

Cheers, Allan

I have cut a bit of glass before, but have never used the clamp that you do. Have you tried just scoring and snapping? The wood on top might be causing the problem. The glass cutters with the diamond tips are normally cheap and disposable, and seem to last only a couple of cuts, so make sure it's a new one that you are using, or if you are going to cut a few sheets, buy one of the better quality ones with the reservoir as mentioned. Mine was about NZ$35.

Thanks boys

Al:
1. The glass is not new. It is actually a mirror in my daughter’s bathroom say 20yrs old. Does it mean it is toughened?

2. I do use lubricant to cut the score line


Big Red:
1. The score is very straight and clean


I use the same technique to cut 2mm glass without any problem. It is just the thick one that I am having trouble with. But next time I will use a good cutter as you both suggested.


Scott

Wongo,

In a past life, I was a glazier.

Get yourself a proper glass cutter, the kind with a small wheel that's about 4-5mm in diameter. Don't buy the ones that don't have a wheel, they're rubbish.

Get an empty shoe polish tin or similar. Put a scrap of felt or cotton waste or something absorbent in it. Dilute some oil with metho and soak the felt with it. Run your cutter back and forth on it to pick up some oil.

Mark your cut with a china graph (white) pencil and get a straight edge that is a few millimetres thick.

Hold the cutter so that it is straight up and down and perpendicular to the glass. Not like a pen. Hold it between your thumb and second finger.

Start a few millimetres in from one edge and run it smoothly along the straight edge and let it drop off the edge of the glass onto your bench. DON't run over the line again. This will stuff your cutter.

Slide the glass across so that the scribed line is directly over the edge of your bench. Grab the offcut side in both hand and push down with a sharp motion.

Tink!!

Practice on an offcut first.

Forgot to say, with thicker glass, you can lift it a little off the bench before you push down. Don't clamp it, it's not necessary and probably accounts largely for the problems you're having.

4mm and 5mm glass is actually easier to cut than 2mm.

Hi Silent
It very hard to take you seriously with your current avatar.
All I can think of is Russell stuffing stuff up, glass cutter, yeah right, I bet all you did was break a window once, hey Russell.

Cheers, Bob

Listen, when The Big Coight says he knows how to do something, he knows how to do it. I don't mess about with fiddly little kid's toys though - when I want to cut glass, I put a tile cutter blade in my circular saw and just rip through it. No mess, no fuss, plenty of blood, just the way I like it.

Hi Silent

At least you'll have enough water to wash the blood off the shed floor.

I wonder who is strong enough to carry 10 L ( 10 kg) of water per km on a hot day. I suppose he'll have watering points set up every 1 km.

cya

Joe

Joe,

2 litres a day on a long walk is heavy enough

Not to mention that you'd probably drown if you tried to drink that much water in one day!

Silent C,

Incredible mate. I have always hated cutting glass because of the possible and eventual stuff-ups. That sure was some good ‘gen’ and I’ll now tackle the task with a bit more confidence. Think I’ll pass on the circular saw and tile cutting blade for a while though!

Made 7 big picture frames (good looking 70 yr old skirting board) last week and needed to cut some glass again last night. I still used the cheap diamond tipped cutter but will buy a good one will wheel when this one is done.

Anyway, I put some engine oil on the tip of the cutter and ran it smoothly along a ruler once and ….tink. The first cut was perfect :eek: and then the second one and the third one ….

Suddenly glass cutting was fun and I think Silent would have been very proud of me.

Another team effort guys

Cheers

On ya, Wongo

I've heard that if you need to cut *really* thick glass, a WRX is the way to go.

Cheers,
Andrew

Originally Posted by arose62

I've heard that if you need to cut *really* thick glass, a WRX is the way to go.

Cheers,
Andrew

Andrew, what is a WRX??