Thread: wardrobe doors higher than 2.4m???

I would say any panel material longer than 2.4m would be a special order. This goes for anything I can think of that you would use for a wardrobe door, including melamine, veneered ply, MDF, mirror etc. Standard sheet size is 2400x1200 (or 8'x4').

You might be able to get them in a joinery door, but it would be a custom order and very expensive.

That is why in older home with high ceilings there is a "filler" at the top. Also to the sides if it is not in modules of 600mm

i thought what iw as getting quoted was already expensive between 3k and 6k for wardrobes with 2 levels of doors... i found a picture of what i want (see attached) I just cant seem to find anyone speaking my language ... have just made more calls and they aare saying at anything higher than 2.4 the timber bows ... is there possibley any type of timber less prone to bow?

Originally Posted by Aangelique1611

Can someone please explain to me why i get either a blank/confused look or a 'no, you cant do that' when i ask for wardrobe doors 2.8m high? I dont get it. Is it an issue of them not manufacturing hinged wardrobe doors to this height? or is it more of a logistics surrounding force issue?

Our ceilings are 2.7m and we have floor to ceiling sliding wardrobe doors, didn't have any hassles getting them. I think they are made from 10mm MDF, 1 is full length mirror.

yeah most have said they can do sliders but not hinged ... any chance you have a picture of your sliders? I have never seen them that tall before so would love a look if you have a pic handy?

I am also in the market for "aftermarket" wardrobes, and have been astounded at the prices being charged by the so-called wardrobe specialists. (approx 1K per 600mm).

You can get doors >2.4m. The cost does go up a bit for materials, but not that much. I guess the issue is that most places make doors based on standard 2400x1200 sheets. So you get 2 doors/panels from this size. However MDF is made in much larger sizes.

Bowing is not an issue if the cabinet is constructed properly. One place I got a quote from uses some bizarre double sheet construction, including steel shanks to strengthen the door construction. This seems overkill to most other places I spoke to. There is no problem, however; getting doors up to 3m in height.

The question seems to be practicality versus cost. Most w/rs are typically 2100 in height or thereabouts. So above that is typically storage. So do you want to see the junk stored up in this area every time you open the tall door? If not, double doors are the go.

On the other hand, the more expensive places charge the same price for any door size - i.e. one 2600x600 door is the same price as 2100x600, so your double your costs to add the small door for the storage area on top. They will also do anything to avoid going over 600mm wide too - I suspect to save money - but there is no technical reason that wider doors can be obtained, if the structure is sound.

The upshot is that you can get bigger doors, some (I would suggest dodgy) places will try to talk you out of it because they can't cope with big sheets. The more up-market places will try to talk you out of two doors to minimise your cost.

Not sure if this helps, but there you go.

Andrew.

rightio ... i'll trya nd ring around the top end of the market and see how i go ... i get a little scared round the big end of town ha! I'll give it a shot ... ps. whats the difference between something like ikea pax and what the wardrobe companies supply? is all all just same sort of frames and doors or is ikea seriously sub standard materials?

From what I recall the Pax is just 16mm whiteboard with pre-drilled shelving holes and plain whiteboard doors. They seemed ok for what they are - a little pricey though. They will never look built in though if that is what you are looking for.

Most cabinet making places will use MDF for the outer shell (for painting/routed panels etc) and 18mm m/r melamine (chipboard) for the internals. Good places will use 1mm rounded PVC edging for the shelves etc rather than the sharper edged stuff.

I will try to find a name for a door specialist - i have it at home. You might have to go via a cabinet maker to order them though - not sure if they deal with the public.You can get 18mm/22mm thickness doors in just about any dimensions.

Andrew.

yup have made some calls this arvo and basically the more upmarket co's are willing to do about 2.7m which i can deal with after bulk head etc... they basically charge what the cheaper co's charge for doors on doors so i guess its much of a muchness (except that i like the look of just one door)

The door company I had been recommended was "Polytech". They seem to have 6 outlets in Sydney. Let me know how it goes.

great, thanks very much for your help! will keep you posted.

Just to confirm, is it the company that looks like it specialises in kitchen doors? http://www.polytech.com.au/ they look like they only have one in sydney ... did a white pages search too and didnt think any looked right? Have you got a web page?

The doors in your pic look like frame construction, and sheet size wouldn't be an issue for that design. The only peculiarity would be longer timbers for the sides of the door. Sides of the wardrobe itself are another matter, though; could likely be butted short panels without esthetic detriment if done well.

Joe

yep. I have a friend who is a cabinet maker, and he gets all his doors - kitchen and wardrobe - from these guys.

best of luck!