Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 12 of 12
Thread: My Evolution Box
-
19th December 2009, 07:42 AM #1New Member
- Join Date
- Nov 2009
- Location
- Southeast PA, US
- Posts
- 6
My Evolution Box
This box was GOING to be a simple maple box with a hinged cherry top to hold a gift. Turns out I didn't have enough cherry so I edge glued some walnut and maple to it to make the top big enough. Then it looked a little weird on the edges so I put the top in an oak frame. Then I thought I'd get crafty and bevel the top of the lid. That was a BAD mistake and I had to fix it with the walnut inlay. I was going to use box joints but figured that with the maple and walnut on top I'd use mitered joints with walnut splines. A couple of coats of shellac and paste wax and this was the result.
All in all, the evolution from the original box turned out reasonably well.
-
19th December 2009 07:42 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
19th December 2009, 08:08 AM #2
Another nice job! I love those projects which cause no end of frustration but turn out OK (or, in your case, better) in the end.
Keep up the great work.
Steve
-
19th December 2009, 08:31 AM #3
Seems like a lot of stuffing around to make a simple Maple box. Nicely put together and the finished piece is really nice
It's only a mistake if you don't learn from it.
-
19th December 2009, 09:35 AM #4Awaiting Email Confirmation
- Join Date
- Jul 2008
- Location
- Central Illinois, USA
- Age
- 79
- Posts
- 65
Nice job of salvaging something that would have otherwise been plain. The glued up top turned out great and the splines really accent the corners. Good job of evolving the project. I find that many of my projects go through an evolution before they are finished.
Thanks for sharing,
Bob
-
19th December 2009, 06:08 PM #5SENIOR MEMBER
- Join Date
- Feb 2007
- Location
- Adelaide
- Posts
- 595
The walnut splines were an inspiration. They harmonised the main box with the lid to very nice effect. I saw that you recessed the hinges fully on the back side of the box and had them just screwed onto the lid. Was there a design reason for not recessing the hinges to half the depth on each face? This is not a criticism, I am weighing the pros and cons of different hinging methods. Incidentally, getting the lid to fit so flat and square was quite an achievement. I could personally use a workshop in getting hinges right like that.
-
19th December 2009, 10:10 PM #6Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Have to agree with Fencepost3. That is anice box.
-
20th December 2009, 12:53 AM #7New Member
- Join Date
- Nov 2009
- Location
- Southeast PA, US
- Posts
- 6
-
20th December 2009, 07:16 PM #8SENIOR MEMBER
- Join Date
- Feb 2007
- Location
- Adelaide
- Posts
- 595
Thanks CD, I see what you mean.
-
21st December 2009, 11:52 PM #9
Very nice. I specially like the splines in the corners of the lid. The overall proportions and mix of timbers is very tasteful.
When all is said and done, there is usually a whole lot more said than done.
-
24th December 2009, 11:54 PM #10
Came out great!
-
27th December 2009, 08:04 PM #11Novice
- Join Date
- Sep 2009
- Location
- Melbourne
- Posts
- 15
I think you can say more than "reasonably well". The box looks great.
How did you do your splines? In particular, from the photos, it appears that the dimensions of the splines are greater than the thickness of the box walls, yet no part of the spline is showing on the inside of the box.
Is this an optical effect of the photo, or did you do some unusual cuts on the splines?
Cheers,
-T.
-
28th December 2009, 12:27 AM #12New Member
- Join Date
- Nov 2009
- Location
- Southeast PA, US
- Posts
- 6
I cut the slots for the splines with a home made jig and cut them straight through. When I set the jig I raised the blade as far as it would go without going through. I guess that makes them a little longer and wider.
Similar Threads
-
Chair evolution.
By Fencepost2 in forum FURNITURE, JOINERY, CABINETMAKING - formerly BIG STUFFReplies: 15Last Post: 2nd July 2009, 12:57 PM -
Lathe evolution
By Zee in forum WOODTURNING - GENERALReplies: 15Last Post: 13th October 2007, 09:17 PM -
SCM C35 Combination Saw Evolution
By Stringy in forum TABLE SAWS & COMBINATIONSReplies: 8Last Post: 11th October 2007, 09:43 AM -
evolution of learning about tool limitation
By havenoideaatall in forum WOODWORK - GENERALReplies: 16Last Post: 24th September 2006, 11:29 PM