Needs Pictures: 0
Results 1 to 15 of 16
Thread: Fitting dividers
-
19th May 2021, 02:50 PM #1
Fitting dividers
I am after opinions on which is the best way to cut the slots when doing halving joints in dividers, or is there a better way of making an intersection other than halving joints.
Currently I cut the slots using the tablesaw providing the pieces are thicker than the blade. I have an Incra Mitre Gauge with the flip stop which I put the end of the divider up against and make the first cut. After this I measure the width of the slot with a vernier to calculate how much more needs to be removed to allow the intersecting piece to fit. I use the micro adjust on the flip stop to push the divider across and creep up on the final measurement rather than one adjustment and find I have gone too far. This seems to be very time consuming and tedious and I was wondering if there are better ways of creating this intersection.
Dividers.JPG
Thanks,Dallas
-
19th May 2021 02:50 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
19th May 2021, 03:15 PM #2GOLD MEMBER
- Join Date
- May 2011
- Location
- Albury
- Posts
- 3,034
A kerfmaker would be the perfect tool for that job. You could either make your own or buy one of the excellent Hongdui models - HONGDUI Kerfmaker Table Saw Slot Adjuster Mortise and Tenon Tool Woodworking Mov | eBay. You may be able to buy one more cheaply elsewhere.
-
19th May 2021, 04:01 PM #3SENIOR MEMBER
- Join Date
- Nov 2008
- Location
- Perth
- Posts
- 543
I'm going to try this method the next time I divide a tray.
Making Jewelry Box Drawer Dividers - YouTube
-
20th May 2021, 07:08 AM #4GOLD MEMBER
- Join Date
- May 2015
- Location
- Brisbane
- Posts
- 1,147
I just cut all the pieces to length first then tape the horizontals and verticals together, mark out the spaces and use a spare piece to mark the width of the cuts by laying it over the top and draw a line down each side. Set the height of the blade and cut between the lines with the pieces still taped together. You might have to take a half hair width off here and there but it works perfectly for me.
-
20th May 2021, 01:07 PM #5
-
20th May 2021, 08:49 PM #6
So it appears there is no secret trick out there that makes this a simple foolproof operation. Because dividers are usually fairly fine things, any error in cutting the width really stands out when they're put together.
No sure how accurately the Kerf Maker would work for such small cuts as I have never used or seen one in operation.
-
20th May 2021, 09:47 PM #7Mug punter
- Join Date
- May 2009
- Location
- Sapphire Coast NSW
- Age
- 69
- Posts
- 434
i suspect kerfmaker would work very well …. i now use, though, the microjig matchfit dado stop …. it is accurate and easy to use …. costs under $50 from timbecon (at least)
regards david
-
21st May 2021, 10:14 AM #8
You must have brought yours some time ago or got a good special as they're now $115. The video on their site does make it look like it works well.
-
21st May 2021, 04:11 PM #9Mug punter
- Join Date
- May 2009
- Location
- Sapphire Coast NSW
- Age
- 69
- Posts
- 434
https://www.timbecon.com.au/micro-ji...-saw-dado-stop
$47.50 ? .. it does work well i use it for all my box and tray dividers but also for other things
regards david
-
21st May 2021, 04:19 PM #10
I picked up the wrong thing. I only saw the kit when I looked.
-
21st May 2021, 04:29 PM #11Mug punter
- Join Date
- May 2009
- Location
- Sapphire Coast NSW
- Age
- 69
- Posts
- 434
i see ... you certainly need to clamp it somehow but i don't recall whether i ever got the other part there ... if i did i haven't used it ... i just use a good square
regards david
-
22nd May 2021, 11:54 AM #12GOLD MEMBER
- Join Date
- Apr 2014
- Location
- Kew, Vic
- Posts
- 1,068
Hi Dallas,
+1 for the kerfmaker. Also, it helps if the lower pieces are a couple of mm shallower (top to bottom) than the upper pieces. This means that the visible cut edge of the joint (the lower piece) is below thetop edge of the upper piece. Looks neater that way.
Regards,
Brian
-
23rd May 2021, 08:04 AM #13GOLD MEMBER
- Join Date
- May 2015
- Location
- Brisbane
- Posts
- 1,147
A867930F-16B4-494A-88B0-C8102D15B0F3_1_201_a.jpg
Using the method i mentioned, fitted like a glove with no movement or rattle.
-
2nd June 2021, 12:07 PM #14
Well I ended up buying the Kerfmaker. Found one for $25 from Sydney so I thought it was worth a go. It arrived yesterday and didn't come with any instructions, but there are a number of videos on Youtube so no problem. Gave it a try on some scrap and the joint was perfect. I will be keen to try it out on a real project.
Dallas
-
10th June 2021, 04:42 AM #15GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Sydney
- Posts
- 1,557
Similar Threads
-
Dividers
By Tyger in forum BOX MAKINGReplies: 7Last Post: 4th April 2017, 06:45 PM -
Callipers & Dividers - How big?
By ventureoverland in forum METALWORK FORUMReplies: 3Last Post: 20th July 2014, 10:14 AM -
Antique 1700's dividers
By DSEL74 in forum WOODWORK - GENERALReplies: 0Last Post: 2nd June 2013, 11:57 AM -
Setting dividers for a PCD
By Michael G in forum METALWORK FORUMReplies: 7Last Post: 7th October 2012, 07:32 PM -
Room Dividers
By tonyp_1964 in forum WOODWORK - GENERALReplies: 3Last Post: 4th November 2011, 10:10 PM