Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 12 of 12
Thread: Inlay strips
-
14th September 2007, 08:56 AM #1
Inlay strips
Okay I been watching the threads in here for some time now and have been really impressed by some of the boxes with inlaid strips in them. To get to the point, I would like to know how to do this and if possible see some pictures of work in progress. Nothing too fancy to start with I just want to inlay a nice strip in a box.
I would be using one of those ready made inlay strips as I don't feel confident enough to make one myself yet.
So how about some easy to follow instructions and some nice WIP pictures.
Reality is no background music.
Cheers John
-
14th September 2007 08:56 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
14th September 2007, 10:22 AM #2
Don't have any training, so take what I say with a grain of salt. What I started with was a scrap piece of 1/2 inch mahogany scavenged from a throwaway table. I cut as thin a strip as I could with my circular saw and straight edge, about i/8 inch. I take my router, mounted on a table, with a half inch bit and set it for a depth a little less than the thickness of my strip. Rout a line, glue the resulting groove, lay in the strip, clamp it and let dry (I find covering it with a little plastic food wrap keeps it from sticking to my sacrifice block). When it's dry I sand or plane flush. It looks more complicated than it is, but the basic line inlay is not too demanding. I hope this is helpful and doesn't set you on the wrong track. I've only done about a dozen inlays so far, but they're not looking too terrible and seem to be getting better.
"If the doors of perception were cleansed everything would appear to man as it is, infinite."
William Blake
-
14th September 2007, 10:57 AM #3New Member
- Join Date
- Sep 2007
- Location
- canberra
- Posts
- 5
Inlay strips
We seem to be asking the same question.
My plan, unless I get better advice as follows:
1. Lid 350 x 250, Frame 40 x 10, Panel 270 x 170 x 10.
2. For the frame I need approx 1200 length of timber.
3. I intend to rout a groove along the length of the frame timber, and then glue in the inlay strip, before cutting to length on the mitre saw.
Hopefully, the corners including the inlay will then match up.
What do you reckon?
Bilby.
-
14th September 2007, 11:04 AM #4
Sounds like it should work, but I would be concerned about damaging the inlay while cutting. I generally inlay after the basic box is made, but then I've always put in edging and gives me a fudge factor for stuff-ups...come to think of it that is why I use edging anyway, I miter somewhat awfully. No table saw and nowhere to put it you see. I miter with a chamfer bit.
"If the doors of perception were cleansed everything would appear to man as it is, infinite."
William Blake
-
14th September 2007, 11:48 AM #5
Thanks Capt Zero. any pics of your work?
Reality is no background music.
Cheers John
-
14th September 2007, 11:51 AM #6
-
14th September 2007, 12:05 PM #7
If you look in boxmaking and pullup 'Crotchwood and wooden hinges' that's some of my more recent work. Leaves some to be desired, but that's not done with a router. You can also check out 2nd box, and 3rd box for some simple router line inlay. Camera's down todaywill try and get some more pics later.
"If the doors of perception were cleansed everything would appear to man as it is, infinite."
William Blake
-
14th September 2007, 06:06 PM #8
Had a look at those, not bad. in fact pretty good.
Reality is no background music.
Cheers John
-
16th September 2007, 06:20 AM #9
Here's different way of doing it. Look at posts 27 thru 30, then the final result at the end of the thread. You can alson see the inlay done on the drawer fronts.
http://www.woodworkforums.ubeaut.com...t=41584&page=3
ICN,
Bill
-
16th September 2007, 12:41 PM #10
This might help a little
http://http://inlays.com/page.asp?id=6
Growing old is much better than the alternative!
-
16th September 2007, 06:08 PM #11
To Munruben,
Dive in and try it, hopefully it will be a success, otherwise the next one will.woody U.K.
"Common looking people are the best in the world: that is the reason the Lord makes so many of them." ~ Abraham Lincoln
-
16th September 2007, 11:17 PM #12
Thanks guys. much obliged.
Reality is no background music.
Cheers John
Similar Threads
-
Timber Inlay Supplier
By wf1 in forum WOODWORK - GENERALReplies: 4Last Post: 24th May 2007, 10:12 AM -
Corrugated steel strips: Where to buy? How to make?
By Peter Dow in forum METALWORK FORUMReplies: 6Last Post: 20th June 2005, 10:28 PM -
Inlay Strips in Sydney
By BobR in forum WOODWORK - GENERALReplies: 4Last Post: 20th September 2004, 03:17 PM -
DECORATIVE INLAY
By DPB in forum WOODWORK - GENERALReplies: 3Last Post: 16th January 2002, 04:59 PM