Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 8 of 8
Thread: Decoupage Box.
-
11th January 2008, 04:39 PM #1SENIOR MEMBER
- Join Date
- Feb 2007
- Location
- Adelaide
- Posts
- 595
Decoupage Box.
I have worked up courage to show a box at last. It is made from American Oak cooper's offcuts, and the lid from jarrah floorboard offcuts. I cut the dovetails with a Gifkin, and made a panel lid, with a 6mm ply panel insert. I have a small hoard of water colour paintings that I receive as Christmas and birthday cards, and so I experimented in glueing them to both sides of the panel, then covering with a glaze of 2-part epoxy. It has come out well enough to send off as a birthday present I think. In future I shall shape the front of the lip to reduce the bulk. I used the golden ratio for the basic dimensions. I welcome any advice on how I can do it better next time.
-
11th January 2008 04:39 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
11th January 2008, 04:44 PM #2Awaiting Email Confirmation
- Join Date
- Jan 2007
- Location
- Goulburn NSW
- Age
- 89
- Posts
- 913
It is a good box well done, my only comment is the timber thickness I would make the box from 10 mm thick stock.
les
-
11th January 2008, 05:02 PM #3
I agree with les88 on the timber thickness, but he's also right ....its a good box..Beaut stuff
-
11th January 2008, 05:07 PM #4
What a great way to reuse those lovely cards. The box is great! why did you wait so long to show us?? It is definintely going to be very well received by its lucky recipient.
cheers
WendyBox Challenge 2011 - Check out the amazing Boxes!
Twist One - Wooden Hinge/Latch/Catch/Handle
Twist Two - Found Object
Twist Three - Anything Goes
-
11th January 2008, 09:25 PM #5SENIOR MEMBER
- Join Date
- Nov 2006
- Location
- t
- Posts
- 961
Top work with the old cards.
Have found that boxes need symmetry though, ie: if lid overhangs, base needs to do same..
-
12th January 2008, 08:39 AM #6
A neat little box.
Nice tight joints.
You could make the lid appear thinner by putting a bevel on the bottom edge - front and sides.
I think a molding around the base might elp the balance.
How do you get the epoxy to flow evenly over the card?
It sounds tricky and messy.Scally
__________________________________________
The ark was built by an amateur
the titanic was built by professionals
-
12th January 2008, 11:27 AM #7SENIOR MEMBER
- Join Date
- Feb 2007
- Location
- Adelaide
- Posts
- 595
Thank you all for your advice(s) about thicknesses, bevels, and balancing. I shall pay attention to that in the next attempt.
Scally, the two-part epoxy came in a pack from Aristocrat, I think there is also a brand called GlassCoat which I have not been able to source.
The surface has to be dead level for even flow of the epoxy, the temperature has to be above 23 degrees for the viscosity to be right (I actually did it when it was in the high twenties, low thirties). The 50/50 thorough mix has to be spot on. Bubbles are a bugger. I waved a small butane pen over the surface to pop the small bubbles about 10 minutes after pouring the mixed epoxy. You can use a toothpick to prick bubbles or a drinking straw to direct some warm breath over the bubble. The epoxy is expensive stuff, but the amount used on a small box is very little.
It's deep (about a millimetre) glossy appearance is somewhat nicer than my simple photography succeeded in showing, I think.
-
12th January 2008, 02:13 PM #8Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
Box
Great box!!
Shouldn't move much, if at all, with that thicker timber.
Similar Threads
-
Decoupage (and other) 'cheat'?
By trcol2 in forum FINISHINGReplies: 4Last Post: 7th August 2005, 12:21 PM -
Decoupage with inkjet images
By echnidna in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 9Last Post: 24th November 2004, 07:15 PM