Thanks: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: Beginner finishing question
-
21st April 2019, 10:40 PM #1Senior Member
- Join Date
- Jun 2018
- Location
- Brisbane, QLD
- Posts
- 196
Beginner finishing question
Hi all,
I have what I’m hoping is a very simple question to respond to. I completed my first proper furniture build a few months back - a walnut coffee table. I decided to finish it with Osmo PolyX in a matte finish as I understood it to be hard wearing. I filled the grain with a paste made from fine sawdust and the Osmo to remove any open pores and proceeded to out 3-4 coats on the table top. I followed an instructional from a recent FWW article.
The finish turned out great, but now to my horror - even the slightest amount of moisture leaves terrible clouded marks!!! It’s not super obvious, but is visible from certain angles when I look along the top.
What have I done wrong? What’s best to fix it? Strip back and start again?
Any suggestions would be greatly appreciated. As it’s my first proper build, the table has a special place in my heart, despite some of its flaws.
-
21st April 2019 10:40 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
21st April 2019, 11:11 PM #2GOLD MEMBER
- Join Date
- Apr 2014
- Location
- Kew, Vic
- Posts
- 1,069
Hi jw,
That sounds very strange. PolyX is usually very protective. I suggest you drop a line to the Osmo distributor in Australia http://www.osmoaustralia.com.au/ They should be able to help. I’d be very grateful if you could keep us posted of what you find.
Thanks and good luck!
Brian
-
22nd April 2019, 08:08 AM #3Senior Member
- Join Date
- Jun 2018
- Location
- Brisbane, QLD
- Posts
- 196
Good idea Brian. I’ve sent an email off.
I was of the understanding that a wipe on poly would be perfect to counteract those accidental spills and provide a robust finish. It’s quite disappointing, especially when I did hours of research on application before applying the stuff. Perhaps user error on my part being new to this stuff.
-
22nd April 2019, 09:00 AM #4GOLD MEMBER
- Join Date
- Apr 2014
- Location
- Kew, Vic
- Posts
- 1,069
jw,
You’re spot on that a wipe on poly would be good for accidental spills. Osmo PolyX, though, is not a poly(urethane) but a blend of hard wax and oils - a very different animal. I still would have expected it to resist the odd spill, though.
Brian
-
22nd April 2019, 01:18 PM #5Senior Member
- Join Date
- Jun 2018
- Location
- Brisbane, QLD
- Posts
- 196
Ah! Right you are, Brian. Notwithstanding, and as you say, I expected a bit more resilience. I’ll wait to see what Osmo says. I’ll keep you posted when I get a response from them.
-
23rd April 2019, 06:05 PM #6SENIOR MEMBER
- Join Date
- Dec 2012
- Location
- Australia
- Posts
- 684
What did you sand the timber to and what was your finishing process?
-
24th April 2019, 07:56 PM #7Senior Member
- Join Date
- Jun 2018
- Location
- Brisbane, QLD
- Posts
- 196
G'day Hurcorh, timber was sanded to 600 in raw state. Applied first coat of oil and let soak for 15 mins or so (as per directons on tin), then sanded while still wet to get a paste going to fill the grain. This worked OK, but not as I had hoped so i let dry, sanded from 240-600 and wiped on a new layer of oil, though this time it was combined with saw dust to create a paste and worked into the grain. I let that dry and sanded (with random orbital sander to 400 grit, then by hand to 600 grit. The grain filled well at this point, so I applied 3 more coats with 1-2 day drying times between coats. I also sanded lightly between coats with 600 and 800 grit to get as smooth as I could. Cheers.
-
24th April 2019, 08:16 PM #8
For what it's worth, try sanding the wood to 600, then add the oil and sand through to 1500-2000. Use the ROS all the way. This should seal the oil into the boards. WIpe down with a cotton cloth and see how that goes. Just a suggestion.
Regards,
Rob
-
25th April 2019, 01:51 PM #9SENIOR MEMBER
- Join Date
- Dec 2012
- Location
- Australia
- Posts
- 684
I sand no further than 180, use the osmo roller to apply a very thin coat. After 24 hrs, buff in another coat with a white abrasive pad and remove excess. After allowing to cure for a week it is very durable.
Similar Threads
-
Oil Finishing for a beginner
By Dave-Ben in forum FINISHINGReplies: 1Last Post: 29th April 2008, 01:07 PM -
Beginner looking for finishing tips
By johnmelb in forum FINISHINGReplies: 9Last Post: 22nd January 2008, 04:28 PM -
Beginner's question
By ciscokid in forum WOODTURNING - GENERALReplies: 5Last Post: 9th March 2007, 11:02 PM -
beginner question: Adding finishing touches to a project
By samfpj in forum WOODWORK - GENERALReplies: 8Last Post: 14th January 2004, 10:39 AM -
Another Beginner - Pine finishing
By AshleyM in forum FINISHINGReplies: 1Last Post: 4th November 2002, 08:17 AM