Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 7 of 7
Thread: dyeing timber or veneer
-
29th August 2013, 05:35 PM #1GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,333
dyeing timber or veneer
Hi. Has anyone had any success dying veneer - or timber generally. The key thing here is that I want the dye to soak in a fair bit - not just sit on the surface. This is so the object can be worked and sanded (a little) without going patchy.
All my experiments to date have managed sub 1mm penetration - probably only about 0.2mm.
cheers
ArronApologies for unnoticed autocomplete errors.
-
29th August 2013 05:35 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
30th August 2013, 09:42 AM #2The Livos lady
- Join Date
- Feb 2011
- Location
- Melbourne
- Posts
- 292
Good morning Arron
What is your project and what is the look you are trying to achieve?
Can you not sand the then stain?
I doubt you will get anything to go deep enough that wont be effected by further sanding.Livos Australia
<O</O
-
1st September 2013, 11:17 AM #3
Hi
Try a thinners based stain.... warm the veneer up if needed, and the stain will soak in..
(Pylon Chemicals "Fast Stain" or the equivalent in another brand)
Geoff
-
3rd September 2013, 11:52 AM #4Jim
- Join Date
- Feb 2008
- Location
- Victoria
- Posts
- 3,191
As you can see from the volume of replies it's not an easy question to answer. I think the deepest stains are achieved when using a product that uses the natural components of the timber - getting a dark blue or black on tannin rich timbers for instance. Just think of the stains around nails in eucalyptus timbers. True mahogany also works with some chemicals. Then again you can create shades in thin pieces by dipping in hot sand - scorching I suppose.
I like vandyke crystals which give you varying shades of brown and being water based can soak in.
Staining can be an esoteric art and it might be best to find a book on the subject.Cheers,
Jim
-
3rd September 2013, 07:43 PM #5GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,333
-
4th September 2013, 09:50 PM #6GOLD MEMBER
- Join Date
- May 2003
- Location
- Central Coast, NSW
- Posts
- 3,333
-
4th September 2013, 10:03 PM #7
Hi Aaron, if it is a warm day (or warm the wood & stain you should get 1 to 2mm...
Unfortunately I have found this out in the past - after first spray customer says "Oh, I didn't think it would be that dark - can you lighten it" and then the sanding starts... and you sand away...
Cold wood, cold stain = less penetration... obviously...
Geoff
Similar Threads
-
Timber or Veneer
By Martin7 in forum TIMBERReplies: 11Last Post: 2nd April 2013, 10:32 PM -
Is It Best To Cut Veneer From Dry Timber Or Green Timber?
By echnidna in forum TIMBERReplies: 1Last Post: 27th August 2007, 09:03 PM -
Finish -- dying or dyeing?
By fts_sjk in forum MUSICAL INSTRUMENTSReplies: 8Last Post: 22nd August 2007, 12:19 AM -
Dyeing timber veneer
By wood chucker in forum FINISHINGReplies: 8Last Post: 29th May 2007, 12:55 AM -
finishing timber veneer
By ml44 in forum FINISHINGReplies: 7Last Post: 3rd January 2004, 07:49 AM