Thanks Thanks:  0
Needs Pictures Needs Pictures:  0
Picture(s) thanks Picture(s) thanks:  0
Results 1 to 4 of 4
  1. #1
    Join Date
    Apr 2019
    Location
    NSW
    Age
    37
    Posts
    1,126

    Default feature grade black butt desk finishing

    Hi everyone

    I'm building my self a computer desk and come shelves out of some feature grade blackbutt timber. this is my rough paint drawing (ignore the dimensions):

    desk.jpg

    i have a few questions about what i should do about finishing it, mainly with regards to the "features" of the wood. As you can see in these pics the blackbutt has a heap of shallow features in it and i'm just not sure if i should fill them or not. I like the features and want to be able to see them.


    Sppk0zl.jpg


    The two options i'm thinking are:

    just pour epoxy over the whole thing, this will will ALL the voids, divots etc and leave me with a totally flat surface, but i'm not 100% sure i'll be able to do this as one pour over the whole thing, as i may need it in two separate pieces to get it in the room. i'm worried i may get a small lip if i try and join the two pieces later if there is a slight difference in thickness of the epoxy.

    or

    use a couple layers of polyurethane, i will still need to fill a few of the larger voids with epoxy but it will also still leave alot of the shallow bits unfilled.


    the desk is just used as a computer desk so no writing takes places on it, so being totally smooth isn't necessary. I can see both methods being just as time consuming as each other. just unsure what might look better.

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Age
    2010
    Posts
    Many





     
  3. #2
    Join Date
    Aug 2007
    Location
    Melbourne
    Posts
    2,178

    Default

    Hi,

    Here are some pictures of a table I made from Black Butt a couple of years ago. The finish is Organoil Hard Burnishing Oil finished using progressive sanding disc grits. While it doesn't fill grooves or gaping slashes in the wood, it will give a very smooth and pleasant finish. You can contact me if you want further information, but please note: I am in no way connected with Organoil Australia, I just like their stuff. Here's some pics of the table top.

    Black Butt table

    Regards,

    Rob

  4. #3
    Join Date
    Jul 2008
    Location
    geelong
    Posts
    359

    Default Fill or no

    For the purpouse desired I would fill the major gum veins only. I have had a cofee table that I deliberately left unfilled (a few veins and nail holes) out of old house frame stuff, just to see how it will go ( is used as a dining table -extends to about a 6 seater table ,2 smokers, drinks etc. It's still Ok with just the poly on it, however filling the veins and nail holes would be recomended. This is a good 10 year run with this as well. Can always be cleaned, but needs a vac and a damp cloth. As an asside original finish was satin poly - now looks more like gloss - yes it will polish up eventualy. (could knock it back with 0000 steel wool -but doesn't worry me.
    Some tint in the resin -if you get it right ends up looking like dried sap. Don't go the black bog, keep it amber and translucent -actually looks beter than clear.

  5. #4
    Join Date
    Apr 2019
    Location
    NSW
    Age
    37
    Posts
    1,126

    Default

    I applied 2 coats of just the cabbots water based floor polyurethane to a scrap bit and it looks good enough for me

Similar Threads

  1. Black Butt table
    By LGS in forum WOODWORK PICS
    Replies: 15
    Last Post: 31st August 2018, 07:38 PM
  2. Feature grade vic ash - which saw mill
    By qwertyu in forum TIMBER
    Replies: 3
    Last Post: 10th August 2018, 08:35 PM
  3. WANTED:VIC WANTED: Feature Grade Spotted Gum Decking 135mm (NO PACK LOTS)
    By barrysumpter in forum WANTED & WANTED TO BUY - in Australia
    Replies: 1
    Last Post: 5th April 2018, 12:53 PM
  4. Jarrah & black butt
    By coffenup in forum WOODTURNING - PEN TURNING
    Replies: 4
    Last Post: 20th August 2017, 01:14 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •