Results 1 to 7 of 7
  1. #1
    Join Date
    Dec 2020
    Location
    France
    Age
    32
    Posts
    2

    Default Sanding plywood to remove Danish Oil

    Hi everyone,



    Here is my problem. I used plywood for a project, stained it (water based, so really easy to remove by sanding), and applied 4 coats of danish oil. Until the last coat, everything was fine, but after the last one, weird shiny wide lines appeared, visible from a certain angle only. I would like to start over the finish.

    My question is : knowing that I used plywood, can I sand my piece to get the bare veneer back ? I'm a little afraid of sanding through it...

    Thank you !

  2. # ADS
    Google Adsense Advertisement
    Join Date
    Always
    Location
    Advertising world
    Age
    2010
    Posts
    Many





     
  3. #2
    Join Date
    Aug 2008
    Location
    Melbourne
    Age
    34
    Posts
    6,127

    Default

    Before you try to get it back to bare timber, maybe try sanding it with 800 grit paper and a bit of oil to try to blend the lines out.

    If the plywood has thin veneers, I don't think you will be able to get to bare timber without sanding through the top layer because the oil doesn't sit on the surface, it's absorbed into the wood. The shiny lines might be the growth rings showing through if the the top ply is saturated with oil (it can't penetrate through the glue to the next layer).

    Can you post a picture?

  4. #3
    Join Date
    Dec 2020
    Location
    France
    Age
    32
    Posts
    2

    Default

    Quote Originally Posted by elanjacobs View Post
    Before you try to get it back to bare timber, maybe try sanding it with 800 grit paper and a bit of oil to try to blend the lines out.

    If the plywood has thin veneers, I don't think you will be able to get to bare timber without sanding through the top layer because the oil doesn't sit on the surface, it's absorbed into the wood. The shiny lines might be the growth rings showing through if the the top ply is saturated with oil (it can't penetrate through the glue to the next layer).

    Can you post a picture?

    Hello elanjacobs, thank you for your answer. I sanded many times with 600 grit paper and steel wool 0000, but nothing seems to help. The veneer is not that thin (1mm for a 18mm plywood, the botton layer on the picture). The other pictures are the same area from various angles.









  5. #4
    Join Date
    Jun 2006
    Location
    East Warburton, Vic
    Age
    54
    Posts
    14,138

    Default

    Weird shiny lines you’re referring to, are natural grain lines in the timber veneer.
    Cheers

    DJ


    ADMIN

  6. #5
    Join Date
    Aug 2008
    Location
    Melbourne
    Age
    34
    Posts
    6,127

    Default


    I don't see anything weird there, just some wavy grain.

  7. #6
    Mobyturns's Avatar
    Mobyturns is offline In An Instant Your Life Can Change Forever
    Join Date
    Jul 2012
    Location
    "Brownsville" Nth QLD
    Age
    66
    Posts
    4,413

    Default






    I agree, just the wonders of working with a manufactured product produced from a natural material. Sanding to remove the DO is not an option, for the reasons given, its a penetrating finish, not a film finish.

    The edges of ply present both face grain and end grain in the alternating ply layers. The "grain" and "cut" of solid wood or veneer determines whether face or end grain or a complex combination of both is present in the face of a board or veneer. Flame, curly, burl, whitebait, compression figure grain present both face and end grain areas on a surface. Those "patches" of the surface "take up" the DO at vastly different rates. It is easy to flood the face grain, but near impossible to flood the end grain, so the end grain will always look dull or flat. Penetrating stains and finishes will always present these application challenges.

    For the face grain drawer fronts the species of wood used, and the "cut" of the veneer, for the face veneers will determine how the DO looks and how the material will "take up" a stain or penetrating finish. Rotary or peeled; crown / rift / quarter / semi-rotary cut veneers all present a different aspect of the woods grain. The nature of the wood, porous, dense, early / late grain growth rings, resin bands, inclusions, etc all modify the "take up" of a penetrating finish. Simply the wonders and challenges of working with a non-homogeneous material - wood! DO may take considerably longer or may never fully cure in patches or bands on some particularly resinous woods.
    Mobyturns

    In An Instant Your Life CanChange Forever

  8. #7
    Join Date
    May 1999
    Location
    Grovedale (Geelong) Victoria
    Age
    74
    Posts
    12,183

    Default



    Hello Aurelius-13


    What you're seeing is called chatoyance (also cats eye or opalescence) as per Tiger Eye semi precious gem stone below. In timber/wood it can be subtle as in your piece of ply or over the top as in fiddleback piece shown to the right of tiger eye. (sorry about the big pic) It is caused by the rays of the light hitting the the wavy grain found in stressed wood, the light rays are reflected back out giving the illusion of depth and movement as it can appear to move when viewed from different angles or positions.

    It is not a fault in your finish or the timber. It is a natural phenomenon/highlight in your veneer. It is also something that is highly sought after in many areas of furniture and woodturning. If you don't want it you have to choose a pierce of dead bland straight grained timber.

    No amount of sanding will remove it. If anything finer sanding may highlight it even more. That's if you can afford the amount of clogged up abrasive it will take to remove the DO.



    Our friction polishes are renowned for bringing out chatoyance in turned work even in dead pan radiata pine. Couple of pics below:


    Cheers - Neil
    KEEP A LID ON THE GARBAGE... Report spam, scams, and inappropriate posts, PMs and Blogs.
    Use the Report icon at the bottom of all Posts, PM's and Blog entries.


Similar Threads

  1. Replies: 2
    Last Post: 10th July 2013, 09:59 AM
  2. Wet sanding Danish Oil into Redgum table
    By Lockwoodsman in forum FINISHING
    Replies: 7
    Last Post: 6th June 2012, 04:04 PM
  3. Marine Plywood vs Baltic Birch Plywood
    By bateau in forum BOAT RESOURCES / PRODUCT SEARCH
    Replies: 7
    Last Post: 9th July 2008, 02:58 PM
  4. Replies: 0
    Last Post: 5th September 2002, 10:43 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •