Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 10 of 10
Thread: Glueing binding to a guitar body
-
10th July 2019, 06:57 PM #1GOLD MEMBER
- Join Date
- Sep 2011
- Location
- Valla Beach
- Posts
- 1,186
Glueing binding to a guitar body
Hi all,
I am looking at putting black plastic binding around the top and bottom of the body for a telecaster style guitar body. The body is made from Australian Red Cedar. I don't want any of the glue running into the ARC as I feel it will make it look all blotchy and of course that wont sand out.
I was thinking the black binding would look great matching a black scratch plate, but I don't want to mess it up.
Any thoughts regarding this and the glue type?
Paul
-
10th July 2019 06:57 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
14th July 2019, 08:50 AM #2GOLD MEMBER
- Join Date
- Sep 2011
- Location
- Valla Beach
- Posts
- 1,186
Decided not to use the binding, after having it almost finished. The ARC looks nice as is.
Paul
-
15th July 2019, 06:40 PM #3Senior Member
- Join Date
- Aug 2008
- Location
- Melbourne
- Posts
- 166
If anyone is still reading, I'm still interested in answers on plastic binding glue types, even though Paul has gone unbound!
-
16th July 2019, 08:34 AM #4GOLD MEMBER
- Join Date
- Feb 2015
- Location
- Strathalbyn South Australia
- Posts
- 1,141
Acetone is what is used, tape binding in place then with a syringe dribble the acetone between the plastic binding and timber. The acetone melts the binding on to the body.
I would prefer to use timber binding as the plastic stuff ends up shrinking over time and comes away from the timber.
-
16th July 2019, 09:48 PM #5GOLD MEMBER
- Join Date
- Sep 2011
- Location
- Valla Beach
- Posts
- 1,186
hi Cal, interesting theory, wouldnt the acetone run into the ARC and leave blotchy marks on it?
Paul
-
16th July 2019, 10:08 PM #6GOLD MEMBER
- Join Date
- Feb 2015
- Location
- Strathalbyn South Australia
- Posts
- 1,141
I don’t think that it would make the plastic binding soak in to the wrc, but I would seal the binding channels with shellac first to stop the acetone running past the channels and evaporate before the binding bonds to the timber. It would only need a light coating of shellac. Try it out on a scrap bit with and without the shellac and see if it works for you. The acetone won’t stain the timber in any way as it will evaporate.
-
18th July 2019, 10:47 AM #7GOLD MEMBER
- Join Date
- Sep 2011
- Location
- Valla Beach
- Posts
- 1,186
Hi Cal and thanks for your comments. I'm not going to worry about the binding now. I've had the guitar together and I think it looks better without worrying about binding. I routered a nice gentle roundover edge around the top and bottom. (as I have seen Telecasters have those). I've put 3 coats of conductive shielding paint into the pickup and electronics cavities. I'm going to buy some ingredients today to make my own WOP and then I ordered a can of Behlens buffing polish. Hopefully this will give me a lovely finish. I did buy a can of spray lacquer, semi gloss, but on testing it out on an offcut of the ARC, the finish was rather flat and dullish. Wasn't that happy with that.
Paul
-
18th July 2019, 11:05 AM #8
for the perfling, to stop glue runoff and penetration, one uses a wipe of shellac.
To glue, use either CA or epoxy. Scrape when dry.
This is exactly what to do for the rosette. No different.
I learned these techniques from:
-- Bogdanovich: Classic Guitar Making
-- Luthiers Mercantile Int'l (@luthiersmercantile)
-- Yvo Haven (@luthierhaven)
and of course StewMac (@stewmac_guitar)
-
18th July 2019, 07:27 PM #9GOLD MEMBER
- Join Date
- Feb 2015
- Location
- Strathalbyn South Australia
- Posts
- 1,141
Except for when gluing nitrocellulose or plastic binding, that is where the acetone comes in to its own, completely compatible with both the above for use as a glue. It bonds the binding by melting the back of the binding into the timber. And I agree about the shellac seal in the binding slot (which I mentioned in my previous post)
-
5th August 2019, 10:39 AM #10
Interesting that all kinds of glue/acetone are being recommended here. I've been using contact adhesive for 15 years simply because that's what Stewmac recommended at the time. Never had any issues with (plastic) binding from it, it bonds the binding into the wood very well. I used to order the Weld-On brand tubes that Stewmac supplied at the time. They don't carry that brand anymore in favour of their own in-house one but won't ship it over air. I've switched to UHU branded one since its available at Bunnings, no problems with that one either, all good.
Similar Threads
-
Guitar body top
By dai sensei in forum CASTING & STABILISATIONReplies: 4Last Post: 30th September 2017, 10:46 AM -
Guitar Body Chanels
By dlannetts in forum MUSICAL INSTRUMENTSReplies: 3Last Post: 21st January 2012, 12:31 PM -
glue question - guitar binding
By old_picker in forum GLUEReplies: 12Last Post: 16th April 2006, 12:09 PM -
Guitar binding question
By old_picker in forum HAND TOOLS - POWEREDReplies: 1Last Post: 7th April 2006, 11:26 PM -
Guitar body
By Strungout in forum WOODWORK - GENERALReplies: 1Last Post: 28th July 2003, 06:40 PM