Needs Pictures: 0
Picture(s) thanks: 0
Results 46 to 49 of 49
-
23rd April 2015, 07:39 PM #46Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
The threading tool arrived yesterday and I had a chance to look at it today. I thought that coming out of the US, the holder was another American device, but looking at the inserts, they are branded "Germany". I did find RB tools doing a web search but they were making card equipment so didn't seem to be the same people. Possibly they are.
P1020935 (Medium).JPG
In this selection I got 4 tools - two 60 degree inserts, an 8tpi acme insert and what looks to be a 4 pitch trapezoidal insert. The holder has metric fasteners on it but also some UNC - perhaps the fasteners were replaced when damaged by using the wrong size spanners in the US?
P1020930 (Medium).JPG
Duplicating the insert backs will be interesting. The grooves are 1mm pitch and inclined at a 17 1/2 degree angle. I imagine the angle of inclination is there to push the insert back into the holder
P1020925 (Medium).JPG
I did think that for a look alike small enough to fit my lathe (the holder height on this is 1 1/2" - RC if you ever buy that 15000mm BC lathe I may have a holder for you) I may be able to do it by mounting inserts in a carrier and pretending I'm cutting a thread on them.A normal M6 has a helix angle of around 3 degrees so for an insert say 25mm front to back I would need to do a 24 start thread to get a similar angle for that pitch. It may have to be milled although with a metric mill that should not be too bad if say 5 or 10 are racked up together.
Michael
-
23rd April 2015 07:39 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
23rd April 2015, 07:48 PM #47GOLD MEMBER
- Join Date
- Jul 2010
- Location
- Melbourne
- Posts
- 7,775
Hi Micheal,
Does the clamping plate have matching grooves?
Stuart
-
23rd April 2015, 07:50 PM #48Philomath in training
- Join Date
- Oct 2011
- Location
- Adelaide
- Age
- 59
- Posts
- 3,149
It does. It's a trapezoid shape with a plain back. The grooves locate on the insert and the plain back surface pulls in against a ramp surface on the tool.
Michael
-
23rd April 2015, 10:46 PM #49Senior Member
- Join Date
- Apr 2009
- Location
- Ballina N.S.W.
- Posts
- 371
Hi Michael,
Very interesting threading tool. Do you think it would be easier to make the tool out of say 4130 enabling you to use a shaper to cut the fine grooves and then braze a piece of square HSS / carbide into it as the cutting edge. It looks like the body of that tool has had a second life as a hammer, some machinists are rough.
Bob
Similar Threads
-
Your best parting tool
By iron bark in forum METALWORK FORUMReplies: 61Last Post: 20th December 2012, 07:40 PM -
Parting tool mounted on rear tool post advice needed
By colbra in forum METALWORK FORUMReplies: 17Last Post: 12th February 2012, 02:49 PM -
1/16 Parting Tool
By Woodir49 in forum WOODTURNING - GENERALReplies: 21Last Post: 8th May 2009, 03:12 AM -
Parting tool used as coring tool
By Tiger in forum WOODTURNING - GENERALReplies: 7Last Post: 25th March 2009, 10:44 PM