Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 15 of 36
Thread: New Closed Handle Design.
-
27th October 2015, 04:26 PM #1Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
New Closed Handle Design.
Recently I posted a preview of the new closed handle design I have been working on.
The following is a progress update; the handle wood is Tas. Pink Myrtle, and the saw plate is 14" x 2 1/2" below the hardback.
The garnet shellac finish is still in the early stages of completion.
The saw plate assembly has only received a rough clean up.
regards Stewie;
-
27th October 2015 04:26 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
27th October 2015, 05:08 PM #2Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
-
28th October 2015, 10:10 AM #3Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Hi Rob. Whats your thoughts on the new closed handle design.
regards Stewie;
-
28th October 2015, 11:08 AM #4Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Yesterday I received a pm from a member of another forum asking if I would send him a scaled drawing of my new closed handle design so he could use it for his own saw making work. I respectfully declined that request.
Stewie;
-
28th October 2015, 12:21 PM #5
Stewie, it's hard for me to say more than appreciate the beauty of the piece from this distance though I do note that by thickening the upper arch of the handle you've spread the shearing forces that the wood fibers are subject to over a greater area cross-section. It appears that the open-handle version is slightly more robust in this area, though it may be the lighting or camera angle.
Cheers,
RobInnovations are those useful things that, by dint of chance, manage to survive the stupidity and destructive tendencies inherent in human nature.
-
28th October 2015, 12:54 PM #6Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
I do note that by thickening the upper arch of the handle you've spread the shearing forces that the wood fibers are subject to over a greater area cross-section.
Hi Rob. A more accurate description; I have focused on beam strength in those critical areas of the handles shape. You will also note the grain direction is where it needs to be located.
Stewie;
-
1st November 2015, 03:46 PM #7Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
The brass back has been hand shaped; stamped; and secured to the saw plate;
The handle has received its final coat of garnet shellac; and will be left for 5 days to allow the finish to harden up before receiving a final buff.
Next on the list is to file and set the saw teeth; 12 tpi; 8* rake angle.
Stewie;
-
2nd November 2015, 12:25 PM #8Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Where the back of the saw plate angles away from the heel of the hardback, a small area of saw plate is normally formed. When mated within the handle mortise this small area of saw plate can cause the hardback to twist slightly as its pushed into the back of the mortise housing. This condition generally causes the toothline to twist out of alignment when mated to the handle. My personal preference is to remove that small area of extended saw plate down to the bottom line of the hardback.
# The above mentioned is based on the assumption the mortise and saw plate slot have already been checked for proper alignment.
Stewie;
-
2nd November 2015, 12:46 PM #9
Hi Stewie,
I occasionally have that happen too when the blade slot becomes misaligned with the back slot. I just start over again.
Cheers,
Rob
Innovations are those useful things that, by dint of chance, manage to survive the stupidity and destructive tendencies inherent in human nature.
-
2nd November 2015, 01:57 PM #10Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Hi Rob. Totally agree. Also; the thinner the saw plate gauge, the less tolerance there is to withstand any degree of slot misalignment.
Stewie;
-
2nd November 2015, 02:09 PM #11
I've also found that the tiniest bit of sawdust at the back of the blade slot can cause deflection of the toothline if it pushes against the inlet portion of the blade, thus cleaning the slot on completion is a must, particularly for the thin blades.
Innovations are those useful things that, by dint of chance, manage to survive the stupidity and destructive tendencies inherent in human nature.
-
2nd November 2015, 02:58 PM #12Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
-
2nd November 2015, 03:45 PM #13
Another great saw Stewie
Well done
Matt
-
2nd November 2015, 05:55 PM #14Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Thanks Matt.
-
3rd November 2015, 04:14 PM #15Deceased
- Join Date
- May 2008
- Location
- Australia
- Posts
- 2,357
Similar Threads
-
Latest backsaw handle design.
By planemaker in forum Saws- handmadeReplies: 26Last Post: 15th July 2015, 12:27 PM -
Possible New Titan Chisel Handle Design Found
By Scribbly Gum in forum HAND TOOLS - UNPOWEREDReplies: 18Last Post: 19th January 2013, 02:28 PM -
Handle Design -- Help!
By RufflyRustic in forum BOX MAKINGReplies: 21Last Post: 11th November 2007, 07:56 PM -
Why the "Why was the Triton service (or lack there of) thead closed?" thread closed?
By Shedhand in forum TRITON / GMCReplies: 7Last Post: 3rd March 2006, 09:09 AM -
Why was the Triton service (or lack there of) thead closed? thread closed??
By Shedhand in forum TRITON / GMCReplies: 1Last Post: 2nd March 2006, 09:56 PM