Results 1 to 15 of 26
Thread: "A Moment At The Seaside" WIP
-
6th May 2019, 06:15 PM #1Senior Member
- Join Date
- Nov 2013
- Location
- Sydney
- Posts
- 261
"A Moment At The Seaside" WIP
A group of visitors to a beach, spot something in the water.....
The group stops. The next movements need a few seconds during which the mechanism which makes the group move will pause. The input speed required slow movement, instead of making a set of reduction gears, a worm gear was created using a store bought large spring which meshed with a ply gear made to drive the crankshaft. Video attached.
Worm Gear.mp4
Thank you for looking,
Gus
-
6th May 2019 06:15 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
8th May 2019, 09:44 AM #2Try not to be late, but never be early.
- Join Date
- Apr 2011
- Location
- Bakers Hill WA
- Age
- 75
- Posts
- 1,079
I love the way that runs. I think you need to turn the leading end of the spring out a little or grind a chamfer to avoid it cutting the gear wheel once it's under load.
Cheers,
Geoff.
-
8th May 2019, 11:20 AM #3Senior Member
- Join Date
- Nov 2013
- Location
- Sydney
- Posts
- 261
Thank Geoff for you input, much appreciated ! Due to the small diameter output gear, and the height of the teeth, only two of the spring windings, the middle two, are in direct contact with the teeth at any one time. The spring, even though it is quite stiff had to be installed onto a timber dowel so I could install it onto a shaft, hence the teeth had to clear the dowel. I remain concerned that long term, the small contact area may wear the gear out. I have yet to see how it behaves under load, I am hoping that worm "gears" have great torque.
Regards,
Gus
-
8th May 2019, 04:18 PM #4Senior Member
- Join Date
- Nov 2013
- Location
- Sydney
- Posts
- 261
WIP The slide mechanism
The beach visitors arrive on a platform which slides on a linear mechanism sourced from a discarded printer during a council clean up. These cleanups are a valuable resource for all sorts of components, this being one, springs, unusual fasteners, linkages, plastic gears etc. Also disassembling them gives many insights into how manufacturers solve mechanical challenges. In this case, the length of the rod turned out to be the exact movement length needed for this automaton.
Thanks for looking,
Regards,
Gus
IMG_1618.mp4
-
8th May 2019, 05:27 PM #5
Another project to watch and enjoy thank you Gus...
You're lucky to have "council cleanups"; up here it's book the pickup, put it out the night before and gone by lunchtime the next day,
so everyone misses out with more to land fill rather than recycling or repurposing!
Cheers, Peter
-
9th May 2019, 08:57 AM #6Senior Member
- Join Date
- Nov 2013
- Location
- Sydney
- Posts
- 261
Hi Peter ! Good to hear from you, thanks for your continuing interest in these fascinating ( for me ) things ! Pity about council cleanups up there, what a waste ! Hope all is well with you,
Regards,
Gus
-
16th May 2019, 11:11 AM #7GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,432
Top Work Gus
Ingenious worm shaft
I love looking at your work and how you can get things to work
Regards
Keith
-
16th May 2019, 06:26 PM #8Senior Member
- Join Date
- Nov 2013
- Location
- Sydney
- Posts
- 261
Keith, Thanks very much for your comment, always appreciate your kind comments, especially coming from a master inventor/innovator !
Regards,
Gus
-
16th May 2019, 06:43 PM #9Senior Member
- Join Date
- Nov 2013
- Location
- Sydney
- Posts
- 261
WIP - Linear movement
The two pin wheels form the engine of the linear movement for the carriage above. The first video shows them without the arm, the second with, and how the pause is achieved. For other actions to take place, and to hold the carriage in place, this 25 second pause was crucial to the actions above. The arm connects to the carriage via stainless steel fishing line routed to opposing sides, around brass pulleys. Return of the carriage is by rubber strand, once the tension is released by the arm.
Thanks for looking,
Gus
IMG_1619.mp4
IMG_1716.mp4
-
16th May 2019, 09:15 PM #10GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,432
Top mechanism there Gus.
Very skilled work
Regards
Keith
-
18th May 2019, 11:21 AM #11Senior Member
- Join Date
- Nov 2013
- Location
- Sydney
- Posts
- 261
WIP - Slide mechanics
There are four characters walking along the beach. The mechanics attached to the slide are the means of control for them. Normally, the platform which serves as the "stage" for subsequent storytelling isn't moving, which makes for relatively simple means of control via cable, lever, cam etc. In this case, whatever movements are achieved by some means of control cannot be directly attached to the slide. The first movement after arrival is a turn by the characters toward what they spotted in the distance. The photo attached shows four brass tubes, to which the characters will be attached, and are then rotated. The brass strips to which the tubes are connected, are pushed by the mechanism seen in the video, controlled by a cam below. Further controls pass through the tubes, from the body of the characters, and emerging through the bottom of the slide, connecting to another mechanism under, and a cam, controlling movement. Electrical cable also will be routed through these.
Thanks for looking,
Gus
Slide upper. A jpg.jpgSlide upper B.jpgTurn.mp4
-
20th May 2019, 06:09 PM #12Senior Member
- Join Date
- Nov 2013
- Location
- Sydney
- Posts
- 261
WIP - Carriage Mechanisms
Once the carriage arrives, two mechanisms serve to create the movements of the four characters. The first video is the view from the top and how the characters turn. The other is of the interior of the mechanism case, looking up under the top panel. As the carriage arrives, the copper linkage connected to its cam, captures the brass element and pulls the telescoping section. This is connected via cables to each character through the tubes and up into the body. The return by rubber is not a success, it places too much load on the slide mechanism, the reject bin got it, back to the drawing board......tomorrow's task.
Thanks for looking,
Gus
Carriage mechanism.mp4
Interior of Slide mechanisms.mp4
-
22nd May 2019, 04:21 PM #13GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,432
Excellent stuff Gus
Regards
Keith
-
29th May 2019, 03:19 PM #14Senior Member
- Join Date
- Nov 2013
- Location
- Sydney
- Posts
- 261
WIP now in recess due to travels, resume August. My thanks to all who followed the process so far !
Regards,
Gus
-
30th May 2019, 02:44 PM #15GOLD MEMBER
- Join Date
- Apr 2013
- Location
- Torquay
- Posts
- 4,432
Similar Threads
-
Plastic "Bung Taps" - I want to "click" a garden hose onto the end of one...?
By Batpig in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 4Last Post: 7th May 2017, 04:05 PM -
An "Oh Wow"moment
By Col in forum WOODWORK - GENERALReplies: 5Last Post: 15th June 2014, 03:20 PM -
A "make Lemonade" moment (I bought a lemon)
By Michael G in forum METALWORK FORUMReplies: 36Last Post: 8th August 2013, 06:24 PM -
"The server is too busy at the moment. Please try again later.'
By SawDustSniffer in forum FORUMS INFO, HELP, DISCUSSION & FEEDBACKReplies: 8Last Post: 18th July 2012, 02:45 PM -
eBay: How long can you "Save" the "Draft"-listing of an item you want to sell?...
By Batpig in forum NOTHING AT ALL TO DO WITH WOODWORKReplies: 0Last Post: 22nd January 2011, 06:04 PM