Needs Pictures: 0
Results 1 to 10 of 10
Thread: Drum Carder
-
2nd May 2021, 11:54 AM #1.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
Drum Carder
Not sure where to put this one.
I milled the timber about 13 years ago, it has a built in tool box, there was turning involved, and lots of metal work components to fabricate, but anyway here goes.
About a month before Xmas 2020 I asked SWMBO if she would like a "Drum Carder" for Xmas. Carders are used by wool crafters tp process raw wool into more useable material for spinning etc.
Hand carders look like large combs and are used to process small amounts of wool at a time and require considerable use of hands/wrists and arms.
Drum carders can process larger amounts very quickly just by cranking a handle and feeding it raw wool.
I looked around at a few Drum Carders on the internet and half decent carders were in the $700+ range so I figured I could easily make one - Ha!
5 months later here it is. It’s based on a $5 Etsy plan, but uses different materials including proper ball bearings.
The most expensive parts are the 7” wide carding cloth (fine spiky wire covered cloth ~$100) and the stainless steel used for all the metal parts.
Based on the $700 RRP above I was working for much less than $5 and hour although I admit to having quite a bit of fun making it and I have never see one like this one, especially using all stainless steel parts.
Pfinished2.JPG
Here's Photo of the other (not quite finished) side, I'm waiting for a 40" long 6mm diam PU belt to arrive and then I will add two SS belt tensioning pulleys and the tensioning mechanism. I have made all the pieces but can't fit them until i have the actual belt in my hands.
Pfinishedq.JPG
If anyone is interested I can provide more details.
-
2nd May 2021 11:54 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Posts
- Many
-
2nd May 2021, 03:08 PM #2China
- Join Date
- Dec 2005
- Location
- South Australia
- Posts
- 4,475
That's a nice looking unit, brings back memories my Mum had one similar many may years ago, used to make her own tapestries, it was just a off the shelf not custom made it was operated by a treadle
"I was working for much less than $5 and hour although I admit to having quite a bit of fun making it"
I think we have all had that problem at some stage.
Re PU belts I am starting to mull over in my head an accurate joining jig, I have had enough of waiting 6 weeks for premade belts to arrive for my Unimat lathe.
-
2nd May 2021, 04:26 PM #3.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
Thought about a treadle, maybe I'll motorise it instead.
"I was working for much less than $5 and hour although I admit to having quite a bit of fun making it"
I think we have all had that problem at some stage.
Re PU belts I am starting to mull over in my head an accurate joining jig, I have had enough of waiting 6 weeks for premade belts to arrive for my Unimat lathe.
-
10th May 2021, 04:54 PM #4.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
The belt finally arrived and I finished the tensioning mechanism.
Complete2.JPG
belt1.JPG
Just after taking the photos I realized the teeth on the big drum are he wrong way around but that's an easy fix - just flipping the drum will do it.
-
10th May 2021, 05:15 PM #5GOLD MEMBER
- Join Date
- Jan 2009
- Location
- Australia
- Posts
- 1,222
Excellent job.
My wife had one exactly the same design.
Wasn't impressed when I got overly eager and overloaded the large drum with carded wool.
The batt was really hard to get off.
I was banned from using it again. My cunning plan worked.....
-
22nd May 2021, 06:52 PM #6.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
More accessories for the drum carder.
A is a awl like tool with a 300mm long, 3/16" diameter SS, thick knitting needle like point and is used to remove wool from the carder in what is known as a batt..
B is a HD wool knot detangler used to partially manually detangle large knots of wool before putting these through the carder.
The metal hook and frame arrangement is SS welded using a TIG welder.
For small jobs like this no SS TIG filler rod is needed as enough of the SS sticks fuses between the pieces to provided sufficient strength for this purpose.
The detangled clips onto the carder main frame so can be located more or less anywhere around the frame.
Accessories2.JPG
Here it teh detangler is seen in its usual working position front of the feed in tray.
Accessories2a.JPG
The green coloured wool is is a batch straight from the dyeing tubs and shows the typical uneven uptake of green dye.
Putting that wool through the carder will blend it into a uniform green
-
22nd June 2022, 02:26 PM #7.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
Last year while making the carding machine describe in this post I made the large diameter pulley (see below) from piece cut from a large Marri slab.
The piece of slab was 45mm thick so I split it in half to get 2 x 21.5mm thick pieces
The piece with the fewest cracks was used to make the large pulley while the other piece lay ended up under a pile of other stuff.
Last week I found it again and decided it might make a good cheeseboard so the first thing was to fill the dozens of mainly tiny cracks. This wasn't so bad as I was filling a few other things with cracks as well an its always easier if one is going a job lot.
ISide1.jpg
The other side is none too shabby either.
ISide2.jpg
-
22nd June 2022, 02:34 PM #8SENIOR MEMBER
- Join Date
- Apr 2021
- Location
- North Qld
- Age
- 61
- Posts
- 682
Not too shabby at all
Lovely wood Bob
The Drum Carder is brilliant..nice job indeed
Log Dog
-
22nd June 2022, 03:00 PM #9.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
-
4th October 2022, 07:16 PM #10.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,796
SWMBO has been needling (wool sculpting) again.
lilldancer.jpg
This is her interpretation of the Bronze (thats why she's browny red) sculpture of the Little Dancer Aged 14 by Degas. Originally sculpted by Degas in wax in the 1880 from which 25 bronzes were made in the years after his death and now on show at many art galleries.
I made the base - supposed to be reminiscent of late nineteenth century ballet school flooring. Wood is pistachio - very dense and sands very smooth, - doubt it's ever been used for ballet school flooring. The figure has a 1.5mm wire armature that also pokes out below the feet. I drilled 1.8mm holes in short (16mmLong) stubs of 1/4" brass all thread and epoxied them onto the wire. The brass allthread pokes though the floor and nuts just under the feet and under the boards and holds everything in place.
Similar Threads
-
Carba-Tec 635mm Wide Drum Sander - Single Drum
By macka75 in forum HAND TOOLS - POWEREDReplies: 6Last Post: 28th October 2021, 10:00 PM -
WDS-4080P Carbatec wide drum sander drum motor replacement
By Lyle in forum GENERAL & SMALL MACHINERYReplies: 3Last Post: 1st May 2021, 05:34 PM -
Looking for a 200 lt Drum?
By aldav in forum DUST EXTRACTIONReplies: 0Last Post: 5th January 2019, 11:13 AM -
What's the drum out there?
By artme in forum SMALL TIMBER MILLINGReplies: 15Last Post: 12th July 2010, 10:14 PM -
Balancing and truing Drum for Drum Sander
By Stetwood in forum HOMEMADE TOOLS AND JIGS ETC.Replies: 11Last Post: 27th May 2007, 11:12 PM