Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 9 of 9
Thread: My Sharpening station...
-
18th November 2006, 07:39 PM #1
My Sharpening station...
Well, pretty boring but got to post something to try and compete with those pesky Pen turners!
For a decade i have been sharpening free hand with 5" bench grey wheel bench grinder that is an ancient Black and Decker 1/3 HP jobby and a couple of diamond hand laps.
Got me by just fine..
I did however always feel that my techniques could yield better results, like an edge that would last longer and not tend to fold over when chopping end grain on Redgum.
So, being a fan of the diamond stones and not being a fan of flattening waterstones , I picked up a couple of cheapy Timbecon diamond plates (360 grit and 1000 grit) and a not so cheapy Norton 4000/8000 grit waterstone.
Total probably around $200..
edit: woops forgot about the Veritas MKII honing jig too, $60 odd...great bit of gear.
Anyway, this little unit should serve me for many a year....
It is just Merbau (pity about the yellow sulphur deposits) because it was within reach , and finished with Danish Oil and Minwax Wipe on poly...
<CENTER>
</CENTER>I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones.
Albert Einstein
-
18th November 2006 07:39 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
18th November 2006, 08:16 PM #2
Looks good Martrix.
Cheers
DJ
ADMIN
-
19th November 2006, 05:17 PM #3
Hi Martrix,
Yep, looks good alright, very professional. And very tidy in that storage box. I also like the look of those shiny chisels, and the very sharp straight edge you have got there. I have already made a mess of one small Japanese chisel by trying to sharpen it freehand on inadequate sharpening gear.
I am in your sort of position prior to your latest setup, that is, grey wheel, old oil stone from my father and the occasional bit of wet and dry on a not so flat bit of melamine. Pretty average results, plus aching fingers.
Think I am going to have to make something up like yours and Derek's setup. Thanks for the photos.
Cheers,
Pops
-
19th November 2006, 05:23 PM #4
That's a nice looking setup, and a beautifully sharpened chisel to boot. Got me buggered how you're going to turn a pen with it though.
Chris
========================================
Life isn't always fair
....................but it's better than the alternative.
-
19th November 2006, 05:28 PM #5
Yes, my results now are much improved and faster to achieve, not to mention repeatable.
The close up of the chisel is razor sharp, and I can ram it into the end grain of Redgum and it remains just as sharp.
I was fitting some door locks last weekend and kept nicking my fingers, even just a light flick on the edge cuts deep.
Its probably quicker to sharpen one chisel freehand, but it comes into its own when doing 10 at once.I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones.
Albert Einstein
-
19th November 2006, 06:47 PM #6
That's a great setup Martrix. How did you attach the plates to the timber?
Tex
-
19th November 2006, 07:06 PM #7
The water stone is a combo so it needs to be flipped over during use, so it just sits in the rebate with about .5mm of play.
The diamond plates are fixed down with spray-on contact adhesive, same stuff used to stick down laminate on bench tops etc.
I used it because if the need to remove it arises, it's simply just a matter of letting some thinners trickle between the two surfaces, and pop! off they come...
Its a handy adhesive, will stick pretty much anything together and stays stuck...
I have actually used it to patch up work trousers, way better than those pathetic iron patches.
I have a spray gun solely for spraying it, and as long as the pot is left full when not in use, you generally don't get any problems with it remaining in the gun for long periods of time..Suction gun only.
Adhesive is Anchorweld Contact adhesive 'High Heat Resistant' spray grade.I know not with what weapons World War III will be fought, but World War IV will be fought with sticks and stones.
Albert Einstein
-
19th November 2006, 09:26 PM #8.
- Join Date
- Feb 2006
- Location
- Perth
- Posts
- 27,792
Not as fancy as Martrix's, but here is my set up. The wooden tray is a mix of Jarrah, Wandoo and crapiata. Sealed with a marine grade poly.
I store the stones in meat keeper type clip lid plastic boxes. During use I sit the stones inside the box lids. See Photo 1. In between the two stones is a 1/2" glass plate with a piece of wet and dry to flatten stones, although after seeing Derek's I think I will replace it with a bit of plaster support mesh.
Photo 2 shows the stones tucked up ready for storage.
Photo 3 shows the tray storage place under a small side bench.
Cheers
Bob L
-
3rd December 2006, 02:52 AM #9
Looks good Matrix. One more thing to add to my shop "to do" list.
Similar Threads
-
My Sharpening Stuff
By Stu in Tokyo in forum WOODTURNING - GENERALReplies: 19Last Post: 20th August 2006, 04:19 PM -
Sharpening....A Dark Side Voyage for Beginners
By NewLou in forum SHARPENINGReplies: 200Last Post: 24th October 2005, 09:55 AM -
Tool Sharpening By Mail?
By Custom Woodwork in forum WOODWORK - GENERALReplies: 4Last Post: 23rd October 2005, 10:14 PM -
Blade Sharpening Survey
By derekcohen in forum SHARPENINGReplies: 0Last Post: 12th April 2005, 04:51 AM -
More on sharpening
By Arron in forum SHARPENINGReplies: 4Last Post: 4th November 2003, 05:04 PM