"Foot Louis XV" on my home made CN 4 axes
Hello everyone
I am happy :U of being able to make you share my first test of machining on my CN in 4 axes, of a foot Louis XV. Test carried out on some 80 mm thickness extruded polystyrene.
I have just assembled a 4iem axis on my CN.:2tsup:
Thanks to this one I can make machinings a little more complex. Here a test of machining of a foot “Louis XV”, traditional of our cabinetmakers…
FXL126-Console-Louis-XV-3-Usinage-4-Axes-Pied-test-CNd'FXL.wmv - YouTube
You can also see the project drawn on Topsolid:
[ame=http://www.youtube.com/watch?v=ujy68e9j2lE&feature=plcp&context=C4c7d257VDvjVQa1PpcFOUVc6AE3XB0Elb6hcKGoekqiK40qEh1UY=]FXL126-Console-Louis-XV-1-DAO-Topsolid.wmv - YouTube[/ame]
PS: the angular adjustment of the 4iem axis has, using “Bevel Box”:
[ame=http://www.youtube.com/watch?v=SOOmcJGfwmU&feature=plcp&context=C41a9bc0VDvjVQa1PpcFOUVc6AE3XB0BXdLpk5D6_TChRh9xmPMp8=]FXL126-Console-Louis-XV-3-Réglage-4-Axes-CNd'FXL.wmv - YouTube[/ame]
Thank you for your comments…
@+ FXL126
Others vidéos on my Youtube chain:
FXL126 - YouTube
FXL126 - YouTube
4iem axis bent Cross-pieces Louis XV
That is there too! The cross-pieces LOUIS XV in oak are finally machined on my CN
After having made a new test on polystyrene, at full speed i.e. maximum 3000mm/mn for axis X and 1500mm/mn for Y, without loss of step for various machinings, it with been necessary that I reduce speed in the oak.
Indeed as of the first trajectories I lost steps in X.
I thus passed maximum speed out of F to 2000 mm/mn, and there more problem of step.
On the other hand, always in the oak, when I was in catch full matter (depth 7mm), I reduced speed F to 800mm/mn, in dynamics with the mouse in mach3.
All this with thus required: 65 minutes of machinings on CN, by cross-piece, for:
- The outlines mills right of 14 mm (back and face)
Mortises for one of the 2 cross-pieces (intended to make the two 1/2 cross-pieces of with dimensions)
Tenons
- Then Strawberry swell of Ø 14mm for the contours of the face, and of against facing
- Lastly, Fraise swell of Ø 8mm, for the drilling of the pivots of installation of the top.
The video it is here:
[ame=http://www.youtube.com/watch?v=ubf0Xp6jHf0&feature=plcp]FXL126 Console Louis XV 5 Usinage 4 Axes Traverse CNd'FXL - YouTube[/ame]
@+ FXL
Others vidéos on my chain:
Chaîne de FXL126 - YouTube
Ça y est aussi ! Les traverses LOUIS XV en chêne sont enfin usinées sur ma CN
Après avoir fait un nouveau test sur polystyrène, à pleine vitesse c'est à dire à 3000mm/mn maxi pour l'axe X et 1500mm/mn pour Y, sans perte de pas pour les usinages divers, il à fallu que je réduise la vitesse dans le chêne.
En effet dès les premières trajectoires j'ai perdu des pas en X.
J'ai donc passé la vitesse maxi en F à 2000 mm/mn, et là plus de problème de pas.
Par contre, toujours dans le chêne, lorsque j'étais en prise pleine matière (profondeur 7mm), je réduisais la vitesse F à 800mm/mn, en dynamique avec la souris dans mach3.
Tous ceci à donc nécessité : 65 minutes d'usinages sur la CN, par traverse, pour :
- Les ébauches fraise droites de 14 mm (contre-parement et face)
Les mortaises pour l'une des 2 traverses (destinée à faire les deux 1/2 traverses des cotés)
Les tenons
- Puis Fraise boule de Ø 14mm pour les galbes de la face, et du contre parement
- Enfin, Fraise boule de Ø 8mm, pour le perçage des tourillons de mise en place du dessus.