Search:
Type: Posts; User: NevilleT
Search: Search took 0.00 seconds.
-
17th July 2020, 11:48 PM
Thread: Triton Router Attachment
by NevilleT- Replies
- 24
- Views
- 5,432
After a few years I finally solved the issue. If...
After a few years I finally solved the issue. If you change the slides on the router table with the indents by drilling new holes closer to the flat section (i.e. to allow the plate to sit lower) it...
-
1st August 2013, 10:52 AM
Thread: Woodworking design software
by NevilleT- Replies
- 10
- Views
- 2,160
Bought the book above and well into the...
Bought the book above and well into the exercises. Will take a few weeks to get through it, but I could not have gotten half the functionality I needed without the book. Good investment for $12...
-
28th July 2013, 07:25 PM
Thread: Woodworking design software
by NevilleT- Replies
- 10
- Views
- 2,160
Woodworking design software
Has anyone come across any good and cheap design software? I tried Sketchlist 3D trial version and it was good but a bit pricey. From memory, there was a hobby version at around $100 and you could...
-
19th July 2013, 03:06 PM
Thread: Triton Router Attachment
by NevilleT- Replies
- 24
- Views
- 5,432
We seem to have run out of puff on this topic. I...
We seem to have run out of puff on this topic. I will include a slightly amended document to conclude the topic in case anyone else has the same issue. Thanks to all those who provided input. I am...
-
18th July 2013, 02:53 PM
Thread: Triton Router table needs a new home.
by NevilleT- Replies
- 9
- Views
- 2,692
If the offer is still open, would be pleased to...
If the offer is still open, would be pleased to take it. Where are you located?
-
17th July 2013, 05:26 PM
Thread: Triton Router table needs a new home.
by NevilleT- Replies
- 9
- Views
- 2,692
Hi Bob Did Brett take the table? I have a...
Hi Bob
Did Brett take the table? I have a Triton Mk3 workcentre and have been having a long discussion on another forum https://www.woodworkforums.com/f153/triton-router-attachment-173661/ about... -
16th July 2013, 12:01 AM
Thread: Triton Router Attachment
by NevilleT- Replies
- 24
- Views
- 5,432
OK. This is doing my head in. Attached is what...
OK. This is doing my head in. Attached is what I think I know. Happy to have someone add to the Word file if it is going to help someone else along the way. In fact when we finish it might be a...
-
15th July 2013, 11:39 AM
Thread: Triton Router Attachment
by NevilleT- Replies
- 24
- Views
- 5,432
Thanks for the comments. To Chief, if you...
Thanks for the comments.
To Chief, if you look at the Triton video mentioned above at about 2:33:30 you will see the router used under the table in the section "Inverter Router Shaper Table".
... -
14th July 2013, 11:14 PM
Thread: Triton Router Attachment
by NevilleT- Replies
- 24
- Views
- 5,432
Good to ask the obvious questions. Sometimes we...
Good to ask the obvious questions. Sometimes we miss the obvious. I have been using the Triton with the saw for some time and the top plate fits without a problem. Seems like there were at least...
-
14th July 2013, 04:06 PM
Thread: Triton Router Attachment
by NevilleT- Replies
- 24
- Views
- 5,432
One more pic. This is how high the workcentre...
One more pic. This is how high the workcentre table is if the opposite end pins are engaged.
-
14th July 2013, 03:45 PM
Thread: Triton Router Attachment
by NevilleT- Replies
- 24
- Views
- 5,432
Firstly thanks to everyone for getting back so...
Firstly thanks to everyone for getting back so quickly. A couple of things.
Someone mentioned the G clamps. If you watch the Triton instructions video at TRITON MK3: Original video from 1984 -... -
14th July 2013, 11:57 AM
Thread: Triton Router Attachment
by NevilleT- Replies
- 24
- Views
- 5,432
Triton Router Attachment
Hi
I picked up a second hand router and slide for a Triton Workcentre. I have a Mk 3 model. When I came to fit it, there is a problem. there are triangular indentations (about 80mm sides) and...