Search:
Type: Posts; User: Jayhawk714
Search: Search took 0.00 seconds.
-
28th June 2022, 01:28 AM
Thread: Question on a picture frame
by Jayhawk714- Replies
- 6
- Views
- 378
Thank you for your reply!
Thank you for your reply!
-
26th June 2022, 08:49 AM
Thread: Question on a picture frame
by Jayhawk714- Replies
- 6
- Views
- 378
Question on a picture frame
I need to build a picture frame but need a little help. The frame is going to have 45* miters. The frame will be 8.5" x 11" on the 4 short sides. What I need to know is how do I figure what the...
-
25th December 2020, 03:50 AM
- Replies
- 4
- Views
- 520
mortise jig
Perfect, I will check YT out. Thanks!!
-
25th December 2020, 03:48 AM
- Replies
- 4
- Views
- 520
mortise jig
Thank you! I will check YT out.
-
24th December 2020, 05:04 AM
- Replies
- 4
- Views
- 520
Need help to find a jig to mortise cabinet/buut hinges
Can anyone guide me to where I can find a jig to mortise for cabinet/butt hinges. I do not care if it is a shop made jig or store bought. I would like it to go from 3/4" wide stock and up. Any help...
-
14th September 2020, 06:59 AM
- Replies
- 2
- Views
- 366
Where to find screw strips for a screw gun
I was given a screw gun but now I need to know where can I find the screw strips for it. I will be using it for 1 1/4" long screws and longer. Any all all help will be greatly appreciated.
-
3rd June 2017, 10:13 AM
- Replies
- 15
- Views
- 1,516
Wow Rob. What a beautiful table. I'm jealous!!
Wow Rob. What a beautiful table. I'm jealous!!
-
3rd June 2017, 10:07 AM
- Replies
- 15
- Views
- 1,516
Thanks again Putty. Get well soon my friend
Thanks again Putty. Get well soon my friend
-
2nd June 2017, 02:19 AM
- Replies
- 15
- Views
- 1,516
Thank's auscab. In my mind the power planer would...
Thank's auscab. In my mind the power planer would be quicker to get the "heavy" material off first.
-
1st June 2017, 02:15 PM
- Replies
- 15
- Views
- 1,516
Need to clarify my question I should have said...
Need to clarify my question I should have said what would be better, a powered hand planer or a belt sander. Sorry for my bad!
-
1st June 2017, 02:01 PM
- Replies
- 15
- Views
- 1,516
Thank's Putty. I will look into that. Would you...
Thank's Putty. I will look into that. Would you by chance have a picture of the router sled you use?
-
1st June 2017, 01:08 PM
- Replies
- 15
- Views
- 1,516
Thank's for your reply. I'll see if I can borrow...
Thank's for your reply. I'll see if I can borrow a hand planer from a friend to try.
-
1st June 2017, 12:44 PM
- Replies
- 15
- Views
- 1,516
Whats best to use. powered Hand Planer or belt sander?
I have several wood slabs I am going to make into a dinning room table and end tables. These have to have a lot of wood removed to get all of the wood saw mill groves out. What do you believe would...
-
5th November 2016, 06:04 AM
- Replies
- 2
- Views
- 940
DW 734 planer cutting head hard to raise
On my DW734 the cutter head will not raise without using a lot of pressure and then there is a loud bang and the cutter head will raise a tiny bit. I have taken off the side panels and cannot see...
-
19th September 2016, 07:58 AM
- Replies
- 6
- Views
- 1,200
Need help on how to square up one edge on rough lumber
I have some rough 1 x 12 lumber that is 6 feet long that I need to keep 6 feet long. Both edges are rough and the width varies by as much as 1/8 " in the 6 foot run, and it might vary that width...
-
30th July 2016, 07:41 AM
Thread: HELP. Need some red cedar veneer
by Jayhawk714- Replies
- 1
- Views
- 472
HELP. Need some red cedar veneer
I am in need of some red cedar veneer. When "red veneer" I mean the kind of red cedar that you line closets with. I am using 3/4" red cedar plywood and need some veneer to cover up the edges with....
-
8th April 2016, 03:50 AM
Thread: Need a hard coat for an outside table
by Jayhawk714- Replies
- 2
- Views
- 1,219
Need a hard coat for an outside table
I built a table out of blue pine and need a finish that will seal it and have a hard/tough finish. The table will be on a covered deck but still might get some rain and snow on it depending which way...
-
5th April 2016, 08:16 AM
- Replies
- 2
- Views
- 1,037
looking for clear base plate for Makita RT0701C trim router
Does anyone know where I can find a clear base plate for my Makita RT0701C trim router. It does not need to be made by Makita, just need one that fits.
Thanks!! -
19th March 2016, 12:22 PM
Thread: Which is better, Dowel or Biscuit?
by Jayhawk714- Replies
- 24
- Views
- 2,708
Which is better, Dowel or Biscuit?
What makes a stronger bond, doweling or biscuits? Or is there any difference? :?
-
2nd January 2016, 05:14 AM
- Replies
- 5
- Views
- 1,114
Where to find a acrylic base for a Makita Compact router
Does anyone know where to find a large , say, 5" or 6", clear acrylic base that would fit a Makita rt0701cx7 Compact router. I would like to use it for my sign making template set.