Search:
Type: Posts; User: johnm64
Search: Search took 0.00 seconds.
-
17th July 2009, 10:00 PM
Thread: Homemade router table mk1
by johnm64- Replies
- 10
- Views
- 2,677
I will eventually put in a couple of Tee tracks...
I will eventually put in a couple of Tee tracks for the fence,and a mitre gauge slot.
Also the fence still has some work to be done on it.
The fence will get some holes or slots for feather boards.... -
17th July 2009, 04:53 PM
Thread: Homemade router table mk1
by johnm64- Replies
- 10
- Views
- 2,677
I spent some time making some trims this week...
I spent some time making some trims this week after work.
I can only spend about an hour or so a night making noise. -
13th July 2009, 11:27 PM
Thread: Homemade router table mk1
by johnm64- Replies
- 10
- Views
- 2,677
Definitely light on the pocket. Yes the doors...
Definitely light on the pocket.
Yes the doors swing in on the suction from the dust extractor.
It gives a clean flow of air to the motor on the Triton.:)
I fitted them up then with a few test cuts... -
13th July 2009, 10:16 PM
Thread: Homemade router table mk1
by johnm64- Replies
- 10
- Views
- 2,677
Surface is 17mm construction ply,courtesy of on...
Surface is 17mm construction ply,courtesy of on of my customers.
I was able to get the top sides and base from the one sheet.
the top is screwed to a sheet of 1200mm x 600mm melamine
courtesy of... -
13th July 2009, 09:44 PM
Thread: Homemade router table mk1
by johnm64- Replies
- 10
- Views
- 2,677
Homemade router table mk1
Evening all, after lurking around the fringes for a while. I thought I had better
show everyone what Ive been working on for the last 6 months, in between
other jobs :rolleyes:
Its not flash ,... -
20th July 2007, 10:23 PM
Thread: gable end and corner cuts
by johnm64- Replies
- 6
- Views
- 2,624
When I did the ends of my shed I fixed the sheets...
When I did the ends of my shed I fixed the sheets into position on one end and cut them by hand with snips while standing on the ladder 3.5m high.:no:
The second end I fixed together on the floor... -
16th July 2007, 12:29 AM
Thread: New Member/New Shed
by johnm64- Replies
- 14
- Views
- 2,376
Shed is rated because we are on the top of a...
Shed is rated because we are on the top of a hill, all eight columns have 500mm x 500mm x 300mmdeep footings ,
then shed floor is poured and re enforced with mesh as well as the slab being
100mm... -
14th July 2007, 01:44 AM
Thread: Jedo's Shed Pt 2
by johnm64- Replies
- 4
- Views
- 1,990
Jedo_3 SWMBO said extend the who are we mere...
Jedo_3
SWMBO said extend the who are we mere males to argue with the boss:o
Noticed the iron but no ironing board:q
If you need a bench , 4 legs on the door and jobs done.
johnm64:) -
14th July 2007, 01:28 AM
Thread: Insulating a Garden Shed
by johnm64- Replies
- 6
- Views
- 10,000
EBS I would be waterproofing the outside ,...
EBS
I would be waterproofing the outside , if you don't I believe no matter what you do on the inside , in time all your studs etc will suffer from dry rot.I would be look at maybe sheeting
the... -
13th July 2007, 12:23 PM
Thread: New Member/New Shed
by johnm64- Replies
- 14
- Views
- 2,376
Thanks again for the comments people, there is no...
Thanks again for the comments people, there is no mistakes only deliberate bits of fire wood :;:q
As far as the wrong delivery address for the shed , the delivery driver said he couldn't read your... -
12th July 2007, 01:38 PM
Thread: Newbie finally sticks head to say Gday
by johnm64- Replies
- 5
- Views
- 1,736
Thanks for the welcome, the beds are where we...
Thanks for the welcome, the beds are where we sleep on weekends as we are also having
a house built on the block.The stubby holder is the camera case as I don't use a stubby holder as my drinks... -
12th July 2007, 01:31 PM
Thread: New Member/New Shed
by johnm64- Replies
- 14
- Views
- 2,376
Thanks for the welcome people , the shed floor...
Thanks for the welcome people , the shed floor was all done on the one day by one of my mates and his offsider.I set the floor level with a luftkin level bought from bunnings.I marked all 8 columns...
-
12th July 2007, 01:53 AM
Thread: Newbie finally sticks head to say Gday
by johnm64- Replies
- 5
- Views
- 1,736
Newbie finally sticks head to say Gday
Thought that after ages of just being a drop in , I thought I'd better say G'day.
Fantastic site :2tsup: great read , hope to eventually give input.
After years of having to work in the steel and... -
12th July 2007, 01:21 AM
Thread: New Member/New Shed
by johnm64- Replies
- 14
- Views
- 2,376
New Member/New Shed
Big hello to all on the site , Ive been nosing around the site for months and have
read some really great info.:cool:
Myself and SWMBO along with our five boys have decided to move so while the...