Search:
Type: Posts; User: tweaker
Search: Search took 0.01 seconds.
-
5th September 2007, 10:44 PM
Thread: jayco dove
by tweaker- Replies
- 4
- Views
- 6,974
replaced the cable and a few pulleys on the...
replaced the cable and a few pulleys on the weekend, all went well. had to wind it up and down and then adjust the cables so the roof was level.
hopefully the next time I spend that long in the van... -
23rd August 2007, 10:35 PM
Thread: replacing laminate
by tweaker- Replies
- 5
- Views
- 2,548
the green probably is fine, but with the orangey...
the green probably is fine, but with the orangey curtains and lino, well you can get the picture.
the old girl just needs a little bit of a modernization:2tsup: -
23rd August 2007, 10:29 PM
Thread: jayco dove
by tweaker- Replies
- 4
- Views
- 6,974
thanks guys, i got the replacement gear through...
thanks guys, i got the replacement gear through camec (very helpful) i'll have a crack and see how i go
-
22nd August 2007, 11:07 PM
Thread: replacing laminate
by tweaker- Replies
- 5
- Views
- 2,548
replacing laminate
I have an "old 1979" jayco caravan with really nice lime green laminate bench tops, is it possible to place newer laminate over the old stuff or would it be better to make new bench tops with new...
-
22nd August 2007, 10:56 PM
Thread: jayco dove
by tweaker- Replies
- 4
- Views
- 6,974
jayco dove
I have an old jayco dove camper trailer that has snapped a cable that raises the pop top, also has a few pulleys with seized rollers (not to bad considering it's a 1979 vintage). what i was wondering...
-
22nd March 2007, 10:49 PM
Thread: plasma cuttrs
by tweaker- Replies
- 8
- Views
- 1,664
i thought that you could also use a compressor...
i thought that you could also use a compressor instead of bottles, is this right??:?
-
22nd March 2007, 10:32 PM
Thread: Link belts
by tweaker- Replies
- 13
- Views
- 2,219
i know the link belt is available in a "b" and...
i know the link belt is available in a "b" and "a" section
-
21st March 2007, 11:11 PM
Thread: plasma cuttrs
by tweaker- Replies
- 8
- Views
- 1,664
plasma cuttrs
has anyone purchased a palsma cutter for home use for around the $1000.00 mark, have seen a couple advertised by BOC gas that can can cut up to 10mm plate but not sure if they are really worth it for...
-
21st March 2007, 11:05 PM
Thread: Link belts
by tweaker- Replies
- 13
- Views
- 2,219
i have used a prodct called nutlink t link belt,...
i have used a prodct called nutlink t link belt, it cost about $50.00 per metre, it has a metal pin wich makes it alot easier to remove a link for adjustments
-
21st March 2007, 10:51 PM
Thread: Welding around diesel tanks
by tweaker- Replies
- 8
- Views
- 5,709
i have heard that its better for the tank to be...
i have heard that its better for the tank to be full than to drain off any diesel or empty, I have seen automotive petrol tanks explode and would definately leave them alone.
-
21st March 2007, 10:45 PM
Thread: Portable Mig Welders
by tweaker- Replies
- 9
- Views
- 6,204
i currently have a lincoln sp170 mig and have...
i currently have a lincoln sp170 mig and have used it for kids go karts to building tandem trailers. i started off with a bottle and normal wire, but you can bet that you will always run out of gas ...