Search:

Thanks Homey
I agree with your suggestions and will also wait a bit before I try anything.

Thanks Homey
I didn't mention in the original post that it is only a couple of small spots from the wax that I use on the screws and, as I'll be using a wipe-on Poly, do you think that the wax that...

Hi Guys/Girls,
While fitting the hardware to a recently completed box, I managed to get some wax on the unfinished timber (Camphor Laurel). Before I just make things worse, can anyone give me some...

Beautiful work. Something to aspire to.

Thanks Mobyturns,
I'm using 4mm aluminium (sometimes 3mm) and I'm not having any issue with discolouration on Silky Oak, probably as it's pretty tight grained. I seem to have succeeded regarding my...

Thanks Chris & Homey. I agree with both of you. I think I'm just getting things a bit hot. I did another test today (with CA glue) and left as small an amount as possible to be ground off - I don't...

G'day all,
I've been experimenting with aluminium & brass splines in some of my boxes and have found that the glue I'm using doesn't handle the heat of the sanding process. Is there any type of glue...

Thanks emmjay. Great advice. Ill keep that in mind when applying the Danish Oil.

Thanks Mpot. Tassierob said the same thing about Danish Oil. Love the card box - very nice.

Thanks Rob. That's exactly the info I needed to move forward. It also confirmed what I thought about other finishes. I'll chase up some Danish Oil & give it a go.
Thanks again.

I've just finished a small box made of Huon Pine and was wondering what finish would be best/safest. I've read (and noticed) that it is a naturally oily timber and as my goto finish is a spray...

Beautifully done!!! Your clients wife will be very happy.

I'm in

Your not wrong CSN. I've been getting my timber from Ken for the last 12 months and have found that ken is very helpful and accommodating if you need something special. His timber is top quality and...

VERY nice :)

Beautiful Hodgo. Where do you source your hardware?

Beautiful work. I'll get there one day:2tsup:

I'm in

Congratulations Guys. Have a great Christmas.

I'm in

I agree with elanjacob. Cut the crossgrain first. It works for me in these cases.

Sounds good. Looking forward to seeing different stages of the build.

Brian

Beautiful work TTIT,
Can you tell me how you produced the panel in the lid? Is it one piece or two?

Thanks
Brian

Hi Ubeaut,
Quick question:
How do you know who won the free stuff giveaway? Maybe I just don't understand the rules.

Thanks
Brian

Thanks TTIT,
I’d certainly appreciate a few pair of those hinges. I reckon if I learn to do it the hard way, when I get the good stuff, it will be a cinch. Of course I’m happy to cover postage, just...

Thanks homes,
Great description. I also noted that Amana are the only ones that have a small diameter pattern bit so I’ll chase up one of those and give your jig idea a go.
Thanks again,

Brian

You're absolutely right - pardon my ignorance.
I saw a video on Youtube using two pieces of MDF. Is it like that? Sorry, I don't know how to make a link to it. And you'd need a small diameter...

G'day homesy,
Could you tell me more about the jig & bit you use. Maybe I could message PM you?

Brian

Go for it homesy. I'm learning something all the time here. I agree with the comment about the knuckle being so prominent. There must be something better. Let's all put our thinking caps on . Maybe...

The shipping cost for two pair of hinges was $10.00.
I’ll post a review on them when they arrive.

Brian

Thanks Homesy,
I’ve ordered a couple of pairs of butt hinges from Gerner. I’ll see how I go. A pity they don’t have side rail hinges.
I’ll keep you posted on my progress (or not)

Thanks ALDAV. Yes, even the "boss" noticed that I should have fitted a key in the lid. Next time :-)

Thanks everyone for the kind comments. Talking about hinges, where can I purchase reasonably priced hardware? I don't seem to be able to find something between "cheap & nasty" and "OH MY GOD".
At...

Beautiful work Dallas. Thanks for showing us.

Beautiful work David. I hope to get there one day.

Hi Guys/Girls,
I finally managed to complete a presentable box. I had posted earlier asking about box proportions as my first attempts just didn't look right but after some great advice from you...

What, me cheat - never :D

I might make up the jig though. Just to test whether it's safe to use :wink:

Brian

Thanks Paul,
Simple but functional. I'll use this to get me going.

Brian.

Thanks for the tip Woodspirit - that's exactly what I've been doing so far.
I think I've convinced the Wife that it's good for the lawn:U

Thanks Jasethebeginner,
Looks like a neat setup. I intend to use this with my Dewalt 735 planer - what do you reckon? I'm only making boxes and tend to take light cuts so I wouldn't think I'd...

Thanks Guys,
Once I get my head around your explanation Homesy135, I'm sure I'll be well on my way. Had a look at the gallery on your site Alexs - beautiful work, something to aspire to. I do have a...

Hi Guys/Girls,
I've been tinkering with boxmaking and really like it. I noticed that my boxes don't look quite right ie. the proportions look wrong. I'm referring to the width/height and wall...

Thanks Ian,
I think you might have sold me on that one. I'll look into it.
Thanks so much for everyones input here. A great site to be a part of.
Brian

Thanks Ian. I'll have a look at that as well. Do you know if it works well on the Dewalt 735 planer?

Thanks everybody and especially to you Lappa for the link. That's a much better idea. I wonder why Dewalt dicontinued it? My Wife is a keen sewer and reckons she can make one of these so I'm giving...

Hi Guys/Girls,
I'm now the proud owner of a DW735 planer/thicknesser and boy, is it MESSY. I don't have a "dust collection system" in my shop (garage) so am trying to put something together that...

Thanks everyone. What a welcoming lot you are :-)

I'm in

G'day Fekit,
I realise it's been a while since you offered those DW735 blades for sale but I just saw it and noticed there was no reply. I don't suppose they're still available?
Thanks

G'day All,
My name is Brian and I'm recently retired. I've always wanted to get into a bit of woodwork and have been getting some equipment together over the last couple of years. I think I've...