Search:
Type: Posts; User: Breaker
Search: Search took 0.00 seconds.
-
1st December 2006, 10:20 AM
Thread: connecting 2 elcheapo compressors
by Breaker- Replies
- 16
- Views
- 3,095
Find it hard to believe you would even consider...
Find it hard to believe you would even consider needing 2 compressors for the above. A paint spray gun that comes with a 5 piece air compressor package ($30 -$50 depending where you buy) will do...
-
13th November 2005, 03:22 PM
Thread: GMC Shopvac
by Breaker- Replies
- 18
- Views
- 3,340
Tex B - Is correct in that the filter in the...
Tex B - Is correct in that the filter in the bucket does work and the vax cannister will be useful for a long time instead having to clean the blocked filter even though there is very little stuff...
-
11th November 2005, 10:27 PM
Thread: GMC Shopvac
by Breaker- Replies
- 18
- Views
- 3,340
Tex B - the drum would work better (I believe)...
Tex B - the drum would work better (I believe) if the inlet with a slightly longer pipe inside than the outlet pipe are both in the lid of the canister (bucket). :cool: Certainly save a lot of...
-
12th September 2005, 03:25 PM
Thread: Information on a Cheap Air compressors
by Breaker- Replies
- 14
- Views
- 13,006
NuPower - yes
I have Nupower 2hp which has a higher upright compressor. :cool: Notice the new 2.5 BigW has a flatter compressor similar to Supa Cheap & Arlec compressors.
Very happy :D with my compressor... -
26th August 2005, 11:14 PM
Thread: Air Compressor & Nail Gun Question
by Breaker- Replies
- 6
- Views
- 4,161
Will run a framing gun no problems. Your motor...
Will run a framing gun no problems. Your motor won't run continuously unless you nail at a very fast rate or have leaking pipe.
-
23rd August 2005, 11:22 PM
Thread: add a fan to an arc welder
by Breaker- Replies
- 4
- Views
- 2,759
The fan will help but a computer fan is hardly...
The fan will help but a computer fan is hardly big enough although the larger fan would help. It is much better blow the heat out of the cabinet. The fan used in the small CIG unit is a fast spin...
-
12th July 2005, 11:53 PM
- Replies
- 18
- Views
- 6,532
Small Karcher - :mad: Had 2 plastic pumps...
Small Karcher - :mad:
Had 2 plastic pumps replaced in unit under warranty and the 3rd plastic pump blew the top 2 months after warranty and they wouldn't touch the unit as they had perform... -
16th November 2004, 11:41 PM
Thread: gmc compressors
by Breaker- Replies
- 1
- Views
- 1,691
The cut out switch is set above 100 psi out of...
The cut out switch is set above 100 psi out of the box.
-
27th June 2004, 02:56 PM
Thread: GMC bench grinder
by Breaker- Replies
- 21
- Views
- 11,281
Still available yesterday at Bunnings Mile End &...
Still available yesterday at Bunnings Mile End & Marion stores in S.A. but not at the above price. Price yesterday for BG200A was $98.30. :o Have been looking weekly since this site showed.
... -
15th June 2004, 05:40 PM
Thread: GMC - in general.
by Breaker- Replies
- 21
- Views
- 7,326
:confused: Ozwinner - What's the story with...
:confused:
Ozwinner - What's the story with the above?? :confused:
Breaker -
7th June 2004, 11:05 PM
Thread: GMC bench grinder
by Breaker- Replies
- 21
- Views
- 11,281
Had trip down to Bunnies at Mile End last...
Had trip down to Bunnies at Mile End last Saturday to find no GMC products with reduced prices. I'll have to stop reading about specials on this site as they don't seem to get to the Mile End store...
-
17th November 2003, 09:26 PM
Thread: Compressor's
by Breaker- Replies
- 16
- Views
- 4,723
The Big W air compressor/ spray paint can/...
The Big W air compressor/ spray paint can/ hose/fittings ($148 in S.A.) seem to work OK as my unit once it re-starts running (83 p.s.i) will continue to spray. Looks as though the pump will produce...
-
5th August 2003, 03:25 PM
- Replies
- 33
- Views
- 10,956
journeyman Mick - The 5" disc from your larger...
journeyman Mick - The 5" disc from your larger 14" original disc seem to powder quickly once they get down in size. Not the same material closer to the centre. My experience.
-
4th August 2003, 12:22 PM
- Replies
- 33
- Views
- 10,956
SupaCheap had then in S.A.. Tool places that have...
SupaCheap had then in S.A.. Tool places that have angle grinder, may be Bunnings, larger Mitre 10, HomeHardware ????:confused:
Have seen at various locations in S.A. especially the 4". The cut is... -
4th August 2003, 12:08 PM
- Replies
- 33
- Views
- 10,956
There are metal devices for mounting an angle...
There are metal devices for mounting an angle grinder to make neat angle cuts which are less than $100. 4" one costs about $30.00. Larger unit for 9" is about $60. SupaCheap?
-
4th August 2003, 11:47 AM
- Replies
- 33
- Views
- 10,956
If your saw has bush bearings. It will not last...
If your saw has bush bearings. It will not last long with metal fillings. :mad:
Metal fillings cut out bush bearings very quickly and there is extra weight/ virbration on bearings cutting metal.... -
1st August 2003, 04:19 PM
Thread: New GMC Compressor
by Breaker- Replies
- 35
- Views
- 12,935
Big W in S.A. has air compressor (oil, 206...
Big W in S.A. has air compressor (oil, 206 lt/p.m., 122lt line supply) with paint spray can and line (nitto fittings) for $148.00. Tank is 24 lt. Very happy with the unit. :D
-
23rd June 2003, 12:45 AM
Thread: Dremel Accessories
by Breaker- Replies
- 7
- Views
- 3,838
Big W in South Australia has 150 piece kit with...
Big W in South Australia has 150 piece kit with various bits, stones, cutter discs, polisher pads for approx $28.00. All in display case with racks.
Breaker -
15th June 2003, 07:33 PM
Thread: ETC Power Tools
by Breaker- Replies
- 0
- Views
- 1,907
ETC Power Tools
Has anybody used Roto Pro Engraver Kit? Seems good value at $50.00 when comparing other kits. :confused:
Has anyboby had any experience with warranty claims?:confused: