Search:
Type: Posts; User: Jerryj
Search: Search took 0.01 seconds.
-
20th February 2013, 10:59 PM
Thread: Done. My DIY loungeroom. Never again.
by Jerryj- Replies
- 3
- Views
- 1,638
Hi Scott What a great job you have done. To...
Hi Scott
What a great job you have done. To continue for 6 months must have been difficult as well. All the best to you, you must be very pleased.
Cheers Jerry -
8th February 2013, 10:11 PM
Thread: How long can you keep Shellac
by Jerryj- Replies
- 3
- Views
- 1,798
How long can you keep Shellac
I made up some blonde shellac several years ago and kept it at the back of a cupboard away from the light, I just wondered if it had a use by date.
Cheers Jerry -
30th September 2012, 02:07 AM
Thread: Question about Infill Plane
by Jerryj- Replies
- 4
- Views
- 1,276
Thanks Peter and Ray, I get the picture Cheers...
Thanks Peter and Ray, I get the picture
Cheers Jerryj. -
29th September 2012, 10:19 PM
Thread: Question about Infill Plane
by Jerryj- Replies
- 4
- Views
- 1,276
Question about Infill Plane
Hi
Please excuse my ignorance. The old Infill Planes do they have bevel down blades ?
Cheers Jerryj -
11th September 2012, 11:24 PM
Thread: Where has the Library gone Please
by Jerryj- Replies
- 2
- Views
- 765
Where has the Library gone Please
Hi
Where has the Library gone please
Cheers Jerry. -
24th June 2012, 11:44 PM
Thread: Help Please Liquid Nails v Stikaflex v ?
by Jerryj- Replies
- 4
- Views
- 2,793
Thanks for the reply Cheers Jerryj
Thanks for the reply
Cheers Jerryj -
24th June 2012, 04:18 PM
Thread: Help Please Liquid Nails v Stikaflex v ?
by Jerryj- Replies
- 4
- Views
- 2,793
Help Please Liquid Nails v Stikaflex v ?
Hi All
I am just making a counter top out of timber to sit on a single brick wall in the kitchen. I would prefer not to have to drill holes in through the top to secure it. Would a construction glue... -
15th December 2011, 08:33 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi Everyone Had a look at my 2 blades and...
Hi Everyone
Had a look at my 2 blades and chip breakers today. Had to open up the slot for the lateral adjuster on both. I used an angle grinder, once the edge was removed it was easy to file the... -
14th December 2011, 10:45 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi Pagie I have sent you a PM regarding your...
Hi Pagie
I have sent you a PM regarding your banking details but not heard back, perhaps you have too many pm's.
Cheers Jerryj -
13th December 2011, 08:00 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi Big Thanks to Peter Pagie, my 2 blades and...
Hi
Big Thanks to Peter Pagie, my 2 blades and irons arrived today.
My Mum said if you cann't say anything nice then dont say anything.... -
12th December 2011, 01:33 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi I have not received my 2 blades and irons yet...
Hi
I have not received my 2 blades and irons yet but I just hope the mail is slow because of the extra Chrismas load. Fingers Crossed
Cheers Jerryj -
6th December 2011, 10:26 AM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi Peter Would you be able to tell me if my...
Hi Peter
Would you be able to tell me if my blades and cap irons will be posted before Chrissy.
Cheers Jerryj -
2nd December 2011, 11:17 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi Peter Was just wondering how all the...
Hi Peter
Was just wondering how all the packing and posting was going, is there many left to do. Keep up the good work
Cheers Jerryj -
29th November 2011, 10:30 AM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi Pagie I live in Bassendean I could distribute...
Hi Pagie
I live in Bassendean I could distribute any blades and iron in the Perth Metro area if that helps.
Cheers Jerryj -
25th November 2011, 11:02 PM
Thread: Ryobi ert2100vk collet issues
by Jerryj- Replies
- 8
- Views
- 4,622
Hi Shannon & Sam As I said before I have the...
Hi Shannon & Sam
As I said before I have the same router and I also have the smaller 1200 ryobi as well. I use the big one mounted in a table and it has had a lot of use with both the 1/2 and 1/4... -
20th November 2011, 02:59 PM
- Replies
- 7
- Views
- 2,061
Thanks very much Pat & Jim Since posting I...
Thanks very much Pat & Jim
Since posting I have come to the same conclusion as you Jim. As my tools blunt I will sharpen them to the setting Tormek suggest and see how I go, as you say I can then... -
19th November 2011, 04:45 PM
- Replies
- 7
- Views
- 2,061
Learning to Wood Turn re sharpening chisels
Hi
I am a beginer at woodturning. Just got a new lathe and need to know how to sharpen my chisels. I have bought a white wheel for my 8" grinder. I have a scheppach 2500 and have mounted a same rail... -
19th November 2011, 03:54 PM
Thread: Feedback on Hare & Forbes Lathe wl-46
by Jerryj- Replies
- 6
- Views
- 2,329
Hi Guys Just to let you know Hare & Forbes have...
Hi Guys
Just to let you know Hare & Forbes have just had their big sale here in Perth. I could not resist (WL-46) as it was discounted by $264.00. At the same time a also purchased a wheel dressing... -
16th November 2011, 10:27 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi Pagie Is it all go do you have the blades and...
Hi Pagie
Is it all go do you have the blades and tapped cap irons, here is hoping you do.
Cheers Jerryj -
8th November 2011, 03:33 PM
Thread: Vicmarc VL200
by Jerryj- Replies
- 2
- Views
- 1,878
Hi Comgreserv I have a 1990 vicmark, mine has an...
Hi Comgreserv
I have a 1990 vicmark, mine has an out board turning and yes it does have an indexing head.
Cheers Jerry -
3rd November 2011, 10:57 PM
Thread: Ryobi ert2100vk collet issues
by Jerryj- Replies
- 8
- Views
- 4,622
Hi guys and gals. I recently purchased one of...
Hi guys and gals.
I recently purchased one of these and I'm generally very happy with it. One critical issue is that the collet does not seem to fit in the spindle well, which allows the collet to... -
7th October 2011, 08:41 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Just wondering if anybody had any news Cheers...
Just wondering if anybody had any news
Cheers Jerry -
28th September 2011, 10:40 PM
Thread: Feedback on Hare & Forbes Lathe wl-46
by Jerryj- Replies
- 6
- Views
- 2,329
Hi Big Shed Tch' and Mimpi Thanks for all the...
Hi Big Shed Tch' and Mimpi
Thanks for all the feedback sounds very good I think I will go and have a look.
Cheers Jerryj -
27th September 2011, 10:37 PM
Thread: Feedback on Hare & Forbes Lathe wl-46
by Jerryj- Replies
- 6
- Views
- 2,329
Feedback on Hare & Forbes Lathe wl-46
Hi
Was hoping to get some feedback from the owners of the Hare & Forbes WL-46 looks good but is it ?
Cheers Jerryj -
3rd September 2011, 08:28 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Any news Please Jerryj
Any news Please
Jerryj -
21st July 2011, 11:57 AM
Thread: Looking for 7/8th dia bright bar
by Jerryj- Replies
- 8
- Views
- 1,668
Thanks everybody. I now have more than enough....
Thanks everybody.
I now have more than enough. Special thanks to Mark I got the steel from Bohler.
Cheers Jerryj -
19th July 2011, 08:39 PM
Thread: Looking for 7/8th dia bright bar
by Jerryj- Replies
- 8
- Views
- 1,668
Hi Guys Thanks for all the replies, I have got...
Hi Guys
Thanks for all the replies, I have got this thursday off so I will contact all the places listed
Cheers again
Jerryj -
19th July 2011, 12:08 AM
Thread: Looking for 7/8th dia bright bar
by Jerryj- Replies
- 8
- Views
- 1,668
Looking for 7/8th dia bright bar
Hi
I'm looking to buy a short lenght of 7/8th bright bar approx 5" or 125mm. Must be 7/8th diameter not 22mm. I have tried a few places locally but know luck, was hoping maybe a forum member could... -
2nd July 2011, 04:04 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Donation sent Cheers Jerryj
Donation sent
Cheers Jerryj -
1st July 2011, 02:17 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi Ts I am happy to make a donation will sort...
Hi Ts
I am happy to make a donation will sort that out today I will send the $6.00
Cheers Jerryj -
29th June 2011, 04:59 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi Thumbsucker, First of all thanks for all the...
Hi Thumbsucker,
First of all thanks for all the hard work you have done for everybody, and its great that it is nearly at an end.
Just one small problem in the latest version of the spread sheet I... -
11th June 2011, 06:32 PM
Thread: The Second Stanley Plane Blade Order
by Jerryj- Replies
- 942
- Views
- 109,199
Hi Thumbsucker First of all thanks for all the...
Hi Thumbsucker
First of all thanks for all the hard work you have done for everybody, and its great that it is nearly at an end.
Just one small problem in the latest version of the spread sheet I... -
7th February 2011, 07:37 PM
Thread: Any ideas on the type of wood?
by Jerryj- Replies
- 4
- Views
- 1,359
We might need to see a photo Cheers Jerryj
We might need to see a photo
Cheers Jerryj -
6th February 2011, 03:34 PM
Thread: Oils aint Oils
by Jerryj- Replies
- 7
- Views
- 1,767
Thanks for all the help I'm going to Carbatec...
Thanks for all the help I'm going to Carbatec tomorrow to pick up large triton router, will have a look for some oil.
Peter I dont have any problem selling the boards or giving them away. Biggest... -
5th February 2011, 01:57 AM
- Replies
- 4
- Views
- 1,805
Wild Dingo I have just been contacted by Carbatec...
Wild Dingo I have just been contacted by Carbatec (Perth) they have more stock of the Large router. I will be picking mine up on monday. Not sure why there is a price drop, was wondering if maybe...
-
5th February 2011, 01:52 AM
Thread: Oils aint Oils
by Jerryj- Replies
- 7
- Views
- 1,767
Thanks Wendy and Charlie. Cheers Jerryj
Thanks Wendy and Charlie.
Cheers Jerryj -
4th February 2011, 02:58 PM
Thread: Oils aint Oils
by Jerryj- Replies
- 7
- Views
- 1,767
Oils aint Oils
Hi I have made a large number of cutting/cheese boards mainly as presents and sold a few at work. I was buying mineral oil from ikea but its not the most convinent place for me to get it from. So...
-
9th January 2011, 11:01 AM
Thread: New Carbatec FM300
by Jerryj- Replies
- 14
- Views
- 2,570
Hi As I said before I have bypassed my switch as...
Hi
As I said before I have bypassed my switch as the DC is situated outside. I have a 10amp pull cord switch located above my table saw so that it is handy to switch on and off. I also use the dc... -
6th January 2011, 12:45 AM
Thread: New Carbatec FM300
by Jerryj- Replies
- 14
- Views
- 2,570
Hi Terminals 13 and 14 have to be joined...
Hi
Terminals 13 and 14 have to be joined together and 23 and 24 also. But of course if you dont feel good about it then get an electrician.
Cheers Jerryj -
5th January 2011, 02:35 PM
Thread: New Carbatec FM300
by Jerryj- Replies
- 14
- Views
- 2,570
Hi I have disconnect my switch and I have added...
Hi
I have disconnect my switch and I have added a pull switch in my shed so I can turn it on as required. I have a pull core switch hanging over my table saw. My dusty is a different make but I... -
16th December 2010, 06:04 PM
Thread: I'm planning to build a Thien seperator
by Jerryj- Replies
- 19
- Views
- 7,010
I all so built a thien seperator, very similar to...
I all so built a thien seperator, very similar to all the others. Its all mounted on the lid. Only this week a friend wanted some sawdust so I emptied the drum. It was about 60% full and the dust...
-
18th October 2010, 10:21 PM
Thread: Scheppach homemade jigs
by Jerryj- Replies
- 3
- Views
- 2,603
Thanks Ern & Artme, its good to make your own ...
Thanks Ern & Artme, its good to make your own
Cheers Jerryj -
17th October 2010, 06:05 PM
Thread: Scheppach homemade jigs
by Jerryj- Replies
- 3
- Views
- 2,603
Scheppach homemade jigs
I have owed the Tiger 2500 a couple of months now and I'm pleased with the machine but (as everbody else say's) the jigs are not the best. Tormek jigs are great but very expensive. So I had a crack...
-
30th September 2010, 10:03 PM
Thread: Looking for info re jointer
by Jerryj- Replies
- 5
- Views
- 2,051
Thanks very much for that Murray Cheers Jerryj
Thanks very much for that Murray
Cheers Jerryj -
29th September 2010, 11:09 PM
Thread: Looking for info re jointer
by Jerryj- Replies
- 5
- Views
- 2,051
Thanks Guys, I was around a another woodies...
Thanks Guys,
I was around a another woodies place yesterday he had a jointer whick was exactly the same as mine sold by carbatec 13 years ago but under the name of Galaxy. So antbody got a manual... -
24th September 2010, 12:37 AM
Thread: Looking for info re jointer
by Jerryj- Replies
- 5
- Views
- 2,051
Looking for info re jointer
Hi I bought a jointer s/h awhile ago and I was just alittle afraid of it, anyway I have pulled it out from the back of the shed and resharpened the blade, squared the fence and checked the table for...
-
12th September 2010, 11:47 PM
Thread: Old Vicmarc
by Jerryj- Replies
- 3
- Views
- 1,870
Thanks Guys
Thanks Guys
-
12th September 2010, 02:26 PM
Thread: Old Vicmarc
by Jerryj- Replies
- 3
- Views
- 1,870
Old Vicmarc
Hi I have recently bought a s/h 20 year old Vicmarc vl175 could any body tell me what thread the main lathe shatf might be
Thanks Jerryj -
18th June 2010, 11:15 PM
Thread: help needed re: CA finish
by Jerryj- Replies
- 7
- Views
- 1,121
Hi Bryce I am very new to turning but have been...
Hi Bryce
I am very new to turning but have been doing some pens, with CA but not using blo. I have had no problems using CA by its self.
Cheers Jerry -
7th June 2010, 12:30 PM
Thread: Just bought my first lathe
by Jerryj- Replies
- 3
- Views
- 918
Thanks for the replies Skot & Artme. Just as I...
Thanks for the replies Skot & Artme. Just as I hoped now I will order a few slimline pens and have a try.
Cheers Jerry