Search:

Some pics would be good, it looks similar to my Jet - 33 SM. The spindle lock is on the right hand side, as you look at the table, to operate the machine.

Post some pics of all 4 sides and of the...

This might seem basic, but engage the spindle lock and use the longest spanner for the nut. Otherwise, soak in what ever penetrant you like and spanner.

I have to wander down and see the new shed, one day!

Matt, you are wise to resist . . . .536863

Some years ago, I brought an infill block plane as a project plane . . . it's still awaiting the roundtoit . . . 536855


Then I got a little 1/2"...

Isn't 2/3rd equal to 66.66666% :q

If Nathan doesn't grab this, I'll be interested, depending on price.

According to the ASIC site, Gregory Machinery is in liquidation.
536291

Sorry to see them go.

Most infill planes than I have ever seen!

Yes, I am, guilty of contributing to the delinquency of another forum member.

I did pick up a few trinkets for myself

1 1/4 (28mm) steel infill shoulder plane

1 1/2 (37mm) Brass Infill...

Sierra's, simple one tube pens, the twist is my favourite, especially in chrome or gun metal platings. Less chance of the muck up fairy visiting.

If you don't feel the cut, then your edge is sharp!

DAMHIKT!

I own the bit, the "ribbing" is a feed rate issue.

What speed are you running the router at?

I run my Spindle moulder and MOF1 at the slowest speed when using this bit.

It is a beast, but...

Hello Paul, yep, the handle is Rock Maple, turned by me. I would hate to think of the postage with a 400mm+ handle, along with the tool.

Hello Paul, in my limited time with the Ukie Slick, after sharpening, it will happily clean up lap joints and tenons in "soft" woods and with a bit more care, some hard woods.

It will also bring...

Stuart at the Tool Exchange, occasionally has US made versions - one on site now.

I have recently brought a Ukrainian version, at a show, on a whim, but cannot remember the proprietor.

534085
...

Dallas, are you "strengthening" the threads with thin CA after cutting?

What TPI is the 1/4", 20 or 24 or 28. Coarser threads work better in timber.

What pilot hole size are you using? In wood...

Turning is a hobby/fun for me. I have turned to order and for markets, I don't need a second job.

Hello Derek, I got the Spindle Moulder out from the naughty corner.


533932 I found a scrap of Rock (Hard) Maple, with saw marks etc

533933 I set up the Segmented Pattern Bit

533934 Spindle...

They are mostly socket chisels or if tanged, I have had to replace handles and hardware.

Tony, KISS principle in action.

I didnt have time to get fancy.

I have one, haven't used it yet. I might use it in the spindle moulder, I'm not game to use it in a hand held router.

Derek, would a segmented pattern bit suffice?

Yep my Pre WWII Wards are very marginally behind the Stubai and Pfeil Bench chisels. My Jap chisels are variable - It's my technique that I have to work on.

Vicmarc have their version.

Hello Matt, Serving tray in Australian . . . :;

I cheated, I planed the reverse to get flat boards, then ran thru the club's helical thicky. Minimal tool marks with that.

Sanded with Mirka Galaxy abrasives #120 -#500, cleaning between grits...

A couple of months ago, dear old Mum asked for 2 charcuterie boards for my niece and her friend.

Then Mum told my sister . . . whom inform Mum and me, that no, 2 boards were not enough, 5 is the...

We get what can be sold readily and for a profit.

If you want something not available in Oz, you then have to order direct and pay the exorbitant postage.

Up to you.

Matt, if I was strong enough, I reckon I lift my Hammer (Bandsaw) with the fence.



Pat

Matt, Cater products have a good line of Bandsaw accessories.

I personally have the Magnetic Fence (II) and the Log Mill. Both good quality - Buy once, cry once price range.

Mine, all mine!

Thanks again B00bby

I'll take it.

Postage?

Sharpening . . . Can of worms opened!

My take, given your Tormek & CBN gear, get the new gouge jig (SVD-186R) and the jig for skews (SVS-50), get good with them, then decide on anything else.
...

Yep, I'll be there, it's only 10 minutes from home.

Andy, you lucky bugger. I would grab that in a heart beat, as a second, as I use mine daily. Perfect for checking square while sharpening, rehabbing chisels and plane blades.

Ok, I'll play, bore out with brace and appropriate bit, then pare the corners to square . . .

What is a Twybil?

Some very interesting conversations and drool worthy toys.

The Ultimate Woodworking Tool Festival : Meet the Blacksmiths in Miki, Japan (??? ??????) Kaji Desse - YouTube

For me, I would clean up the backs first, so the Ura (the dark concave part of the back) is clearly visible. Easy on the larger chisels, on the narrower can be challenging. I would sharpen, via...

I turn pens at max speed on what ever lathe (Stubby 1000 or Woodfast 305), with a 12mm P&N skew. Normally start the polishing at Abranet #400.

When I had my Woodfast M910, the tacho said max was...

I put my dusty into it's own little shed, behind the main shed.
I ported thru the adjoining walls, which may not be an option for you.

There is another, specific steady for longer spindle work, with 4 wheels and encaptures the entire job. I'll have to see if I can find a pic of it, somewhere. I have seen them used on jobs up to 8.5...

Vid worked for me, sounds raspy!

hello rod, I have sent a message asking the same detail on facebook to Stihl Timbersports.

Which belt did you end up with? I it's an "A" section like my 1000, I'm going to replace it with a power twist link belt. I've done this on a few of my older machines, saw, thicky, spindle moulder (I...

On a mini lathe, 372w (1/2HP) is enough, given the physical limitations of the lathe.

That's a good purchase.
I don't need more G clamps and the club wasn't interested in them.

Haven't you moved, yet?

Avion, what email address did you use?

Was it? "stubbylathes" at "ampengineeringsolutions.com.au"

(Replace the "at" with the ampersand and remove the quotation marks and spaces)

I also...

Each or All?