Search:

Type: Posts; User: sysiphus

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    419

    N.S.W. Carbatec CT-38 15" Thicknesser

    My old man is selling his thicknesser. No idea of the actual age of the device, was purchased second-hand in 2010 and has done 3/5ths of fudge-all since then.
    It's in good condition, apart from...
  2. Hi Folks, Thought I’d close the loop on this...

    Hi Folks,
    Thought I’d close the loop on this one, with the news that I gave up. No matter what I tried I couldn’t get the bloody things out, so I took it to the Authorised Repairer here in...
  3. So firstly remove the retaining circlip from the...

    So firstly remove the retaining circlip from the other end of the cutter block shaft. Then you should be able to drive the cutter block shaft from the end you originally pictured out of the housing...
  4. Thanks for the pointers, folks. I finally managed...

    Thanks for the pointers, folks. I finally managed to get back into the shop to take another crack and.. no dice :(

    The cutter head is definitely a larger diameter than either end of the...
  5. Sure thing! It's basically the same as the other...

    Sure thing! It's basically the same as the other end - doesn't look like the shaft slides through or anything
  6. How to replace bearing on a Jet 12" thicknesser? (JWP-12)

    Hi Folks!

    I scored a good condition JWP-12 from these very forums.. unfortunately, after running one piece of pine through it one of the bearings gave up the ghost :(
    459850

    After much trial...
  7. QUEENSLAND Timber - silky oak and meleluca (ya gotta slab it)

    Hi there,

    A friend of mine is about to have some trees professionally cut down - a silky oak (trunk at least 6m) and some melelucas a bit smaller.
    She's engaged an arborist to bring them down,...
  8. Replies
    4
    Views
    1,893

    QUEENSLAND Pm sent

    Pm sent
  9. Replies
    4
    Views
    1,930

    Over 200 views and no suggestions? Not even a...

    Over 200 views and no suggestions? Not even a ballpark?

    :(
  10. Replies
    4
    Views
    1,930

    Bunya Slab price

    Hi Folks,

    Dad has a large slab of Bunya pine he wants to get rid of, but neither of us have the faintest idea what a fair price would be. Dimensions of the slab are 2740 x 930 x 50 (0.127 m3),...
  11. Replies
    37
    Views
    6,360

    Moot point again, but all the other curves are...

    Moot point again, but all the other curves are 'inward' (to the piece), so having those 'outward' would look odd. Not sure if an inward-curve on the ends would work either, mind...
  12. Replies
    17
    Views
    11,885

    If I was still in Brisbane, I could offer to......

    If I was still in Brisbane, I could offer to... lend.. you some space to.. store.. the bench. Yes... store... you'd get it back.

    Honest ;)

    (unfortunately, I'm in Mackay until next year,...
  13. Replies
    0
    Views
    975

    Lost - workbench howto/WIP site

    Hi Folks,

    I've been trying to find an article I read on the Intarwebs a couple of years back, which I'm pretty sure was linked from here. I've had no luck finding it, however, so I was hoping...
  14. Replies
    1,193
    Views
    371,515

    He's talking about the hole for the handle, which...

    He's talking about the hole for the handle, which he drilled before routing the rails. So the rail depth needs to be sufficient for the drilled hole to line up.
  15. Replies
    7
    Views
    7,391

    I'd suggest checking out the sister Renovation...

    I'd suggest checking out the sister Renovation forum (Renovate Forums). I just did a search over there for "bamboo deck" and there are a lot of results, looks like there might be some useful...
  16. I'd hazard a guess that Whitworths should have...

    I'd hazard a guess that Whitworths should have what you're after. They're in Balaclava St, Wooloongabba (just over the road/corner from Glenfords!).
  17. Replies
    13
    Views
    3,294

    Thanks to another forum member, I've actually...

    Thanks to another forum member, I've actually acquired a 2000 workcenter.... and it's already attacked me! Hadn't had it more'n 24 hours before the piece of sheoak I was practicing with came back at...
  18. Replies
    13
    Views
    3,294

    You're a champ Russ, I might yet take you up on...

    You're a champ Russ, I might yet take you up on that offer ;)
    I actually went table-saw shopping today, having bid on that Makita a little and immediately losing out ;) Took a good long look at the...
  19. Replies
    1
    Views
    1,216

    workcenter 2000 saw chassis

    G'day All,

    Went shopping this morning to the Big Green Shed closest to me, and they had a display 2000 for sale... the offered it to me for $300 as it only had half its legs (!), but when we...
  20. Replies
    13
    Views
    3,294

    Yet another newbie table saw question....

    G'day Ladies and Gents,
    Over the Christmas break I'm afraid I came down with that most vicious of diseases, the woodworking bug. Consequently, I suddenly find myself in the market for a tablesaw;...
Results 1 to 20 of 20