Search:

I don't understand how I continue to see teaching videos where the woodworker runs a board through a dewalt planer without using sacrificial wood for snipes.

Tile adhesive.

Okay, I tried the white version of liquid nails, whatever that is, and it was a bust.

I like magnets or construction adhesive.

I filled the matrix under my saw table with glued on shapes of wood so I would have a way to use clamps on the table. I have tried all kinds of different glues to hold these odd shaped pieces of...

How to unsubscribe from a thread that has been answered

​thank you. Good idea. I have some red.

I'm restoring an old doll house. I have to remake, remodel, the stairway that uses tiny spindles to hold the railing. I need something that will hold the spindles in place (balusters) while I measure...

I have a 15/64 straight router bit, rockler. I placed it in an extension of the Router Raizer like I have done hundreds of times with other bits. I was making a grove in the underside of a box piece....

504972504973

I made two jigs for my table top router. One uses a miter slot and the other uses a v shaped opening. I bought a spiral bit. The miter slot jig is scary but seems to work ok with a dowel hole in the...

I have now tried several blades. Two were perfect. One is near perfect. Two new blades are more of an issue. Now the question is how much teeth marks are acceptable? I don't think I've ever looked so...

What is a collar.

Bought a new sawstop. My freud 24 tooth rip leaving some teeth marks on edge. Bought two CMT blades highly recommended by skilled woodworker on internet. this is when I began noticing the teeth...

6"
No more discussion is needed as you answered my question.

I'm puzzled. I have a steel city cabinet saw. It has the opening around the throat plate for the blade. It has another opening in front for the height adjustment wheel. To the right is a door that a...

I have a big cyclone. Its worst on the table saw. It works as well as I can expect I guess but there's always plenty of sawdust inside the saw cabinet.

Its very difficult to reach the gears so I use the new wd40 version with the long nozzle. It's supposed to liquify on use as I understand it. I've never used a dry lubricant.

I have as steel city cabinet saw. It gets hard to crank up the blade. I blow it out and lubricate it. It doesnt take long for it to get hard to crank again. Any ideas?

I have an adjustable square that wont stay tight. I've tried loctite. I tried writing to the manufacturer and got no reply.

I'm puzzled by one small twist drill bit. It is much more aggressive than any of my others. It often runs off without me going too deep. Sometimes I can't pull it out on the forward setting and it...

474162That was some of the best advice I've ever gotten. I can use it from now on. By the time I finished the project you cant even see the edging. It looks like it came out of a furniture store.

I can't tell, but I think I added a photo.

I created (a monster) a heavy, stiff, walnut mantel. The beveled corners are pretty good but open. What would be the best lasting filler? Would timber mate be sufficient? I'm afraid it will just...

I started a new cleat system. I loaded the first project with 9 chisels. It wants to lean forward. Do I need a piece in front of the base to hold it in place?

I have purchased Sungold sandpaper several times. but, I've noticed that even though it says Aluminum Oxide, it wears out extremely fast. I'll have to stop buying this junk. Any comments that would...

There are MANY video posts with top notch wood workers counter sinking t nuts and drill holes for the claws. In the videos there is plenty of room for these holes. I have to admit I save used...

should I assume it's not okay to throw a good file into a tray of files?

I've watched many wood workers predrill holes for the claws on t nuts. By the time I drill holes for the t nut shaft there's not much wood left around the shaft. The holes I drill get pulled into the...

Thank you for the art work. In my venue, it will be simpler to maybe throw a bolt on top of the tube that slows evaporation and just add water from time to time. I have a water tap in my shop. Also,...

Oops, I've been using the wrong "reply" button.

Are you an engineer? This makes no sense to me. I'm not an engineer. I dont know what your talking about but I would like to. It may be helpful.

Confused. One end goes into an opening cut into the cyclone. I would have thought that would have provided a breathing hole.

What sensor are you talking about? This is a rubber tube that has no propensity to fail.

I have used a harbor freight dial gauge to square my table saw. I've been wondering if there is any difference using a more expensive gauge.

I made a manometer and it has worked well. I'm having a little issue right now. It appears that when I add a plug to the tube to avoid evaporation, the water moves. Should I assume that you can't use...

This sounds reasonable but it's a puzzle why this has to be done when I make the runners cutting both sides alternately several times.

These keeps happening. I have a nice steel city table saw. When I make a jig using runners, the runners feel right except in a spot or two. In order to allow the runners to move freely I have to...

I've thought about that

I've tried it on ash and grade a pine. I always have hooks

I've do e this.

Yes to all. Carbide burnished. I just watched a guy use a file on the edge only and get beautiful shavings. I tried it. So far the same or minutely better then before.

I've been watching videos. I've been taking notes. I can't get my two scrapers to produce shavings. I'm continuing to read.

I actually tested tg ed tox on 10/24 tester. Must be misaligned threads.

Barely found a 10/32 threaded rod. The vendor was sure although his in store size was listed as 3/16. The 10/32 nuts are struggling to fit. I have not yet finished filing the threads on the rod but...

Fir. Ordinary 2x4s

I got a new bit but not any advice from Freud. I flattened a bench of laminated 2x4s with a 1 3/4 straight bit. By the time I finished, the corners of the bit looked worn. The deepest cut was maybe...

I re read the instruction manual and found nothing relating to 3/4".

I thought I should be able to plow or clean a 1/2" groove as an example. But the scate stops the blade from reaching that depth and that's before sharpening it. I don't understand why Lee valley...

I bought the Veritas combination plane. I was disappointed only in that the blade reaches no further than 3/8 of an inch. Lee Valley keeps telling me I can make it go further. It was suggested I...