Search:
Type: Posts; User: gatesy
Search: Search took 0.00 seconds.
-
24th February 2019, 04:49 PM
Thread: New thicknesser
by gatesy- Replies
- 8
- Views
- 4,439
New thicknesser
Howdy all,
I know this subject may have been covered in many different posts before but haven’t seem to found one source.
Long and short I’m going to commit to a thicknesser. Been on the list... -
8th July 2018, 01:29 PM
Thread: Sink cut out measurements
by gatesy- Replies
- 5
- Views
- 1,291
Sink cut out measurements
Hi all just a quick one and more curiosity than anything. I’m going to be finishing a kitchen bench top soon and I’ve been given the cut out measurements as 1144 x 494 mm CR=20.
My only assumption... -
2nd June 2018, 09:28 AM
- Replies
- 2
- Views
- 1,143
Panel clamp, sash clamp, pipe clamp, steamed clam-ps?!
Hi all, bit of a re-post request as unfortunately arniew’s clamps weren’t suitable.
Long and short I’m making a 3m benchtop for a friend of mine. I have 3 large frontline clamps, which are great... -
30th May 2018, 02:53 PM
Thread: Frontline panel clamps
by gatesy- Replies
- 1
- Views
- 1,091
Frontline panel clamps
Hi All,
Wondered if there were any panel clamp - ideally frontline clamp owners in Melbourne who would be keen to help me out?
Long and short I’m in the process of designing and making a new... -
30th May 2018, 02:39 PM
Thread: Triton router service/repairs Melbourne
by gatesy- Replies
- 4
- Views
- 2,476
Big delay but thanks for all the comments. The...
Big delay but thanks for all the comments. The chocolates however go to @elanjacobs who solved the issue. Brushes were the issue, and they were ordered and installed. Easy as. Cheers folks!
Sent... -
16th May 2018, 10:03 PM
Thread: Triton router service/repairs Melbourne
by gatesy- Replies
- 4
- Views
- 2,476
Triton router service/repairs Melbourne
Evening all,
After advice or experience in getting tools serviced in Melbourne. Specifically I’ve got a newish (5 years) triton router which is having issues after heavy use, and now has stopped... -
25th September 2017, 12:52 AM
Thread: New front door
by gatesy- Replies
- 4
- Views
- 884
New front door
Evening all. I’ve been promising swmbo for a while I’ll make a new front door...finally I’ve caved! She’s seen the design as per the pic, but wanted to get thoughts on ideal timber (prefer HW),...
-
31st January 2017, 04:37 PM
Thread: Osmo over epoxy
by gatesy- Replies
- 8
- Views
- 10,023
Thanks stephen, I'll take a look and see how the...
Thanks stephen, I'll take a look and see how the West System varies from other epoxies. Cheers.
-
31st January 2017, 02:27 PM
Thread: Osmo over epoxy
by gatesy- Replies
- 8
- Views
- 10,023
Stephenw111 - Did you get any response from...
Stephenw111 - Did you get any response from anyone, or did you have a crack at your project. Doing somethign simaliar myself, would love to know the answer!
-
8th April 2016, 09:30 AM
Thread: Jarrah posts oil
by gatesy- Replies
- 6
- Views
- 1,295
Jarrah posts oil
Hi all, just a quick one I'm hoping someone has had experience with. I'm just finished building a pergola, using jarrah posts. They're in great condition just wondered what oil/finish would be best....
-
24th March 2016, 11:31 PM
Thread: Advice on Freestanding pergola plans
by gatesy- Replies
- 2
- Views
- 867
Advice on Freestanding pergola plans
Evening All,
I know this isn't the general woodworking theme but I figured a lot of you will be like me, so might be able to add a bit of experience on my upcoming project!
I am planning on... -
22nd September 2015, 08:24 PM
Thread: Which Screws would you recommend?
by gatesy- Replies
- 1
- Views
- 652
Which Screws would you recommend?
Hi All,
Just after a little general advice. I'm in the process of building an outdoor table for a friend. Steel legs (like a steel square at either end not individual legs), and the top is... -
8th September 2015, 11:38 PM
- Replies
- 1
- Views
- 3,969
Sketchup plans - Triton workcentre crosscut sled
Hi Guys,
I have searched and read many a post, just wondered if anyone had any sketchup designs for a cross cut sled for the triton workstation. I have found a few designs, i.e people posting... -
18th August 2015, 07:24 PM
Thread: Simple steel tube table legs.
by gatesy- Replies
- 9
- Views
- 918
Hi Guys, The exact size is flexible depending...
Hi Guys,
The exact size is flexible depending on price. I've attached a couple of sketches I did, was hoping someone could offer some assistance what would be cheaper. All measurements are just a... -
18th August 2015, 04:37 PM
Thread: Simple steel tube table legs.
by gatesy- Replies
- 9
- Views
- 918
Simple steel tube table legs.
Hi all, First time I've crossed the fence from the woodworking forum, hoping someone can help! I'm building an outdoor dining table for a friend, who wants metal legs! Not simply 4 legs but a steel...
-
18th August 2015, 04:19 PM
Thread: Mitre joints
by gatesy- Replies
- 3
- Views
- 1,322
Mitre joints
Hi all, after a little advice on mitre joints. I'm building an outdoor table and bench seats, and the legs for the benches are going to be s loop of timber at either end as opposed to 4 legs. I'm...
-
26th March 2015, 11:37 AM
Thread: Roubo bench - Purchase.
by gatesy- Replies
- 1
- Views
- 1,510
Roubo bench - Purchase.
Morning All,
Just wondered if anyone here in Oz has made their own Roubo split top work bench, or has even purchased one. Am starting to get into furniture making, and whilst I like the idea of... -
9th January 2013, 01:00 PM
Thread: First Table saw - Advice seeking!
by gatesy- Replies
- 6
- Views
- 1,442
Hi Andy, thanks for that. When you say you...
Hi Andy, thanks for that. When you say you upgraded to work on larger pieces what would be the biggest piece you could work on, on a Bosch GTS 10?
I don't want to buy something I will grow out of... -
9th January 2013, 11:46 AM
Thread: First Table saw - Advice seeking!
by gatesy- Replies
- 6
- Views
- 1,442
First Table saw - Advice seeking!
Hi all,
Wonder if anyone can offer some advice on purchasing my first table saw. I am looking to purchase my first table saw, and on a little bit of a budget <$500 ideally, but flexible. Looking...