Search:
Type: Posts; User: danielhobby
Search: Search took 0.01 seconds.
-
3rd June 2015, 04:13 PM
Thread: New project - Diesel tank
by danielhobby- Replies
- 20
- Views
- 2,491
just one last point to make in this fine thread...
just one last point to make in this fine thread and that is to consider using pickled and oil sheet.It will save you a lot of cleaning of the scale flakeing etc
-
26th November 2014, 12:00 AM
Thread: mild steel to stainless steel
by danielhobby- Replies
- 8
- Views
- 1,657
id say give it a go mate.if its only joins that...
id say give it a go mate.if its only joins that are accesable easily enough then have a crack.ive welded many many items together with gas shielded mig and steel wire when it hasn't been important...
-
20th October 2014, 10:55 AM
Thread: Melbourne Area
by danielhobby- Replies
- 3
- Views
- 2,062
Hi Allan,what area are you from and what calibre...
Hi Allan,what area are you from and what calibre are you planning on?
-
16th September 2014, 05:23 PM
- Replies
- 7
- Views
- 1,562
2014 aluminium welding procedure required
I am looking for a welding procedure for 2014 alli,its possible it is 2017 grade also. I HAVE SEARCHED TO THE LIMIT OF MY ABILITY AND PATIENCE ON THE INTERNET and am now putting it out there for an...
-
7th July 2014, 01:48 PM
- Replies
- 21
- Views
- 5,220
and the original correct expansion of RHS Is...
and the original correct expansion of RHS Is rolled hollow section being square or rectangular,little rant over.
-
7th July 2014, 01:45 PM
- Replies
- 21
- Views
- 5,220
Can I offer my experience of 40 years of...
Can I offer my experience of 40 years of Boilermaking / fabricating. Make your trailer from rhs black material (unpainted)if you can get it.Leave your large ends open and drill or blow large air...
-
25th June 2014, 05:24 PM
Thread: Lathe inspection in Melbourne
by danielhobby- Replies
- 4
- Views
- 1,592
Hi Robin,what suburb does this lathe live in?
Hi Robin,what suburb does this lathe live in?
-
17th June 2014, 01:47 PM
Thread: Tig Advice
by danielhobby- Replies
- 24
- Views
- 5,210
Oh and I'm a foot pedal man, I'll tape it to my...
Oh and I'm a foot pedal man, I'll tape it to my foot before I use a switch.
Pulse what pulse my foot shakes enough not to use it.
Honestly I thought I needed it but have played with it and came... -
3rd April 2014, 07:29 PM
- Replies
- 25
- Views
- 3,345
as an add to this post,try BMS in Campbellfield...
as an add to this post,try BMS in Campbellfield for a quote.They do oxy profile cutting and also water jet cutting.Alliance laser in Campbellfield can cut 16mm no probs and have a 12.00mtr x1.500mtr...
-
24th March 2014, 04:01 PM
Thread: Angle Grinder Fatality
by danielhobby- Replies
- 38
- Views
- 6,256
could be a sign of the future...all Metro trains...
could be a sign of the future...all Metro trains (Melbourne train operator)maintenance depots have a blanket ban on 9'' grinders on SITE...no use..no possession.thankfully 5'' and 7'' grinders have...
-
17th February 2014, 08:26 AM
- Replies
- 5
- Views
- 2,957
The gun is marked not with no 4 or numbers etc,...
The gun is marked not with no 4 or numbers etc, rather strange. Just marked350amp.3.6 mtr long.i have two no 4's on a safmig and a cig and a no two on an old three phase 180 amp cig machine.the...
-
17th February 2014, 12:09 AM
- Replies
- 5
- Views
- 2,957
My 195 rural pack came oe with a "350 amp" tweco...
My 195 rural pack came oe with a "350 amp" tweco gun,a great gun too.tweco no 4 tips liners and shrouds etc fitted correctly.ive not seen this gun on anything else.id guess and say in between 2 ad 4...
-
14th February 2014, 06:21 PM
Thread: teflon liner in bulk?
by danielhobby- Replies
- 10
- Views
- 2,135
hi graham I didn't mention the machine is a 210...
hi graham
I didn't mention the machine is a 210 amp unimig procraft,its duty cycle is still pushed but its surviving so far.im finding a variation with the amps output when I look at the readout... -
6th February 2014, 08:52 AM
Thread: teflon liner in bulk?
by danielhobby- Replies
- 10
- Views
- 2,135
hi graham ive got quite a few rolls of old 1.2...
hi graham
ive got quite a few rolls of old 1.2 mm alli which have oxided slightly and this leaves an oxide residue in the liner.im using a hanging wiper on the wire pre driver roller and the job... -
4th February 2014, 03:52 PM
Thread: teflon liner in bulk?
by danielhobby- Replies
- 10
- Views
- 2,135
teflon liner in bulk?
Hi all,does anyone know if it is possible to buy Teflon liner in bulk?i only use 1.2mm ally and haven't had any luck on fleabay etc
-
4th February 2014, 03:47 PM
- Replies
- 6
- Views
- 2,291
I would imagine that pre setting an angle of 92...
I would imagine that pre setting an angle of 92 degrees inside as graham suggests would be successful.no gap would be essential and clamp solid if possible.Maybe trial and error will flush out the...
-
9th October 2013, 11:23 PM
Thread: Failing Vision
by danielhobby- Replies
- 6
- Views
- 2,125
brasso and silvo also do a...
brasso and silvo also do a brilliant(https://www.woodworkforums.com/images/icons/icon6.png)job.while we are on the subject,i have fitted a boc magnifying lense under my polycarb cover to aid my...
-
9th October 2013, 11:17 PM
Thread: help needed please.
by danielhobby- Replies
- 6
- Views
- 1,647
I had to do a pick up today from my laser cutter...
I had to do a pick up today from my laser cutter and it dawned on me that they also make springs so I asked the obvious question and they handed me over four for free,hows that for quick...
-
9th October 2013, 08:49 AM
Thread: help needed please.
by danielhobby- Replies
- 6
- Views
- 1,647
thanks bob,much appreciated
thanks bob,much appreciated
-
9th October 2013, 12:03 AM
Thread: help needed please.
by danielhobby- Replies
- 6
- Views
- 1,647
help needed please.
hi all.i have a job to do that requires telescopic handles on a very exspensive hand truck and need to know the name of the spring loaded double pin clips that one would find in tubes like...
-
19th August 2013, 10:18 PM
Thread: Sporterising a Swedish Mauser
by danielhobby- Replies
- 25
- Views
- 9,433
I would add onlu one point to an informative...
I would add onlu one point to an informative discussion,and that is that a 29" barrel is fine in some quarters of shooting but as a sporter it is very long when combineing a longer butt on a sporting...
-
1st August 2013, 12:15 PM
Thread: Daniel's J.A.Fay Bandsaw.
by danielhobby- Replies
- 20
- Views
- 4,481
Glad you can put it to good use rob, belonged to...
Glad you can put it to good use rob, belonged to a close friend of my father who was an extremely talented german woodworker/stairmaker.he left it with us to repair and then he died.he'd be glad its...
-
31st July 2013, 12:05 AM
Thread: Daniel's J.A.Fay Bandsaw.
by danielhobby- Replies
- 20
- Views
- 4,481
g,day matty and you too rob, Matty I reckon your...
g,day matty and you too rob,
Matty I reckon your a bastard for making me sell that saw,im missing it badly,you should never have raised the issue of selling it.
The one and only consolation is that... -
17th July 2013, 03:47 PM
Thread: Vintage vs Imported..
by danielhobby- Replies
- 31
- Views
- 4,303
-
23rd May 2013, 11:20 PM
Thread: Vintage vs Imported..
by danielhobby- Replies
- 31
- Views
- 4,303
hi matty,hows things?The old fay is still going...
hi matty,hows things?The old fay is still going strong.cheers
-
5th April 2013, 09:51 PM
Thread: Which Multitool Linisher Attachment?
by danielhobby- Replies
- 84
- Views
- 13,707
ive got a915 x 50 on an old cmf 8 inch bench...
ive got a915 x 50 on an old cmf 8 inch bench grinder,it gets used solidly every day.i also have a three phase 5hp 2740mm x 75 linisher and i like the little one better.
-
27th March 2013, 11:14 PM
Thread: Machinability of MIG weld
by danielhobby- Replies
- 14
- Views
- 1,363
i would suggest(from my own exp) that you have...
i would suggest(from my own exp) that you have welded mig deposits onto cast iron.When i did the same by accident thinking what i had was an old piece of cast steel i broke tips and could not budge...
-
4th March 2013, 10:03 PM
- Replies
- 3
- Views
- 5,138
i purchased a pac 50 from token tools last year...
i purchased a pac 50 from token tools last year and have used it nearly every day since and i cant fault it so far.ive used it and abused the tips on cutting 310 ub 46 beams as well as on1mm...
-
4th March 2013, 09:51 PM
Thread: Use for stainless steel LPG car tanks
by danielhobby- Replies
- 20
- Views
- 3,017
hi all,im happy to stand corrected here but from...
hi all,im happy to stand corrected here but from memory gas tanks are tested to appro480 psi(YES IM OLD)for a working pressure of 120 psi.I would add that these tanks will most likely be out of test...
-
26th February 2013, 11:36 PM
Thread: Etched brass name plates
by danielhobby- Replies
- 21
- Views
- 2,193
hi all,ive seen copies available on ebay.they are...
hi all,ive seen copies available on ebay.they are of original size and correct gear/feed specs and come from southbend origin usa if my memory is correct.
-
3rd February 2013, 09:21 PM
Thread: 7016 vs 7018 what's your experience
by danielhobby- Replies
- 10
- Views
- 6,848
graham thats a great idea for a new thread!...
graham
thats a great idea for a new thread!
what parts of our body we have burnt and stuck to other parts when pos welding and oxy cutting etc. -
8th January 2013, 11:03 PM
- Replies
- 8
- Views
- 3,936
x2
x2
-
31st December 2012, 08:23 PM
Thread: Larger disposable cylinders
by danielhobby- Replies
- 10
- Views
- 2,186
and that is long enough for me
and that is long enough for me
-
29th December 2012, 07:08 PM
Thread: What am I doing wrong
by danielhobby- Replies
- 17
- Views
- 3,265
Graham has given you a perfect guideline to ...
Graham has given you a perfect guideline to cutting your plate,all i would add is that the scale on that plate looks odd to me,either very thick or not mild steel or down grade or something like...
-
29th December 2012, 06:53 PM
Thread: Larger disposable cylinders
by danielhobby- Replies
- 10
- Views
- 2,186
I have used a single bottle of pure Argon...
I have used a single bottle of pure Argon purchased for $69 from supergas.My use was for site tig welding ally scaffolds and i thought i would try it once.My findings are,its difficult to get enough...
-
21st November 2012, 10:07 PM
Thread: Gate design issue
by danielhobby- Replies
- 5
- Views
- 2,317
try Goliath self closeing hinges,not sure what...
try Goliath self closeing hinges,not sure what retail is but its nowhere near that price.
-
9th October 2012, 09:05 PM
Thread: sheraton serial number AR111M
by danielhobby- Replies
- 6
- Views
- 1,129
thanks pipeclay,im wondering if its a mongrel...
thanks pipeclay,im wondering if its a mongrel bitsa as the owner says it has a sheraton named plate on the gearbox.
-
9th October 2012, 08:19 PM
Thread: sheraton serial number AR111M
by danielhobby- Replies
- 6
- Views
- 1,129
sheraton serial number AR111M
236175hi all,does anyone have the info on above serial no sheraton.lathe is called a model a junior according to its owner.ihavent seen it so only have photo to go by.thanks,danny
-
8th October 2012, 10:31 PM
Thread: sheraton junior
by danielhobby- Replies
- 0
- Views
- 857
sheraton junior
has anyone heard of a sheraton "junior"lathe?
-
20th September 2012, 09:54 AM
- Replies
- 6
- Views
- 3,415
50x50 x1.6 or 2mm in gal finish will be ok,its...
50x50 x1.6 or 2mm in gal finish will be ok,its not the size of the tube but the desighn which counts.make sure you put a diagonal brace from top outside to bottom middle in each panel(even 10mm rod...
-
1st September 2012, 11:04 PM
- Replies
- 16
- Views
- 5,519
i have some 50 mmod ss tube bends(1.6mm wall)...
i have some 50 mmod ss tube bends(1.6mm wall) that are pretty damned good that i got from "swadesir" in thomastown.they are 180 degree and aprox120 mm od radius.maybe look him up.i cant help you with...
-
9th August 2012, 12:08 AM
Thread: hdpe machineing
by danielhobby- Replies
- 1
- Views
- 826
hdpe machineing
i have a job to quote and am not familiar with one aspect of the job,machining hdpe round bar.i have to get it to a tolerance of about .5mm on 150diam about 350mm long.will it behave?it will be...
-
29th July 2012, 09:51 PM
Thread: A little question
by danielhobby- Replies
- 10
- Views
- 1,898
are you useing splits or sticks?
are you useing splits or sticks?
-
24th July 2012, 11:54 PM
Thread: Alloy Cylinder head repair
by danielhobby- Replies
- 5
- Views
- 2,694
as the robber says,remove ALL corrosion and make...
as the robber says,remove ALL corrosion and make sure its back to pure alloy.
preheat gently and thouroughly allow heat to soak and preheat again.i have mig welded 6 cyl falcon heads but i recomend... -
17th July 2012, 11:44 PM
Thread: Safety Question
by danielhobby- Replies
- 27
- Views
- 4,200
i have an old lincoln "portable" 240volt jet...
i have an old lincoln "portable" 240volt jet which draws aprox 4400 watts start up current on a 3.2mm gp rod setting(flat out).didnt do slow blows or breakers at arc strike but will at 10 seconds...
-
23rd June 2012, 09:29 PM
Thread: welding flash
by danielhobby- Replies
- 4
- Views
- 1,918
i would agree with karl in that mig is worse than...
i would agree with karl in that mig is worse than stick in general.I know when uv burns on my upper chest are concerned,mig is worse,I always assumed it was because the arc and weld pool with mig...
-
21st June 2012, 11:09 PM
Thread: This is for metal workers too!
by danielhobby- Replies
- 43
- Views
- 3,524
i will simply say that there are quite a few very...
i will simply say that there are quite a few very carefull operators out there that have lost a digit or two and up until that micro second of red mist they belonged to the" it wont happen to me"...
-
21st June 2012, 10:50 PM
Thread: Flat belting
by danielhobby- Replies
- 47
- Views
- 4,193
thank you for posting that,i have a denbigh...
thank you for posting that,i have a denbigh camelback and that technique may come in handy for a save one day.
-
16th June 2012, 06:49 PM
Thread: Current Aluminium Price
by danielhobby- Replies
- 10
- Views
- 4,255
i normally find that per kg price ranges between...
i normally find that per kg price ranges between $7.50 and $11.00 depending on quantities purchased and grade required and wether its extruded or rolled product.a 3mm floorplate 1200x2400 is about...
-
7th June 2012, 09:02 AM
Thread: Magnetic Chuck Rebuild
by danielhobby- Replies
- 21
- Views
- 4,841
i used to work for eriez magnetics in...
i used to work for eriez magnetics in cambellfield/melbourne.they are normally good people to deal with.i have another contact who recos chucks from home and if you need i can contact him,pm me if...