Search:
Type: Posts; User: Elleff
Search: Search took 0.00 seconds.
-
20th November 2013, 01:12 PM
Thread: Festool dust extractors
by Elleff- Replies
- 9
- Views
- 2,584
Owner of new Toy........(Absolutely Vital Safety Equipment)!!
Hi All Again,
A big Thankyou to all who responded to my query!
The feedback was excellent and is of great assistance when trying to spend more money than your wife would like. Even the... -
18th November 2013, 06:53 PM
Thread: Festool dust extractors
by Elleff- Replies
- 9
- Views
- 2,584
Festool dust extractors
Hi All,
I recently had the pleasure of using someone elses FESTOOL Dust extractor and was suitably impressed. I have a FESTOOL router and and a Domino and would now like to attach them to one of... -
26th July 2012, 06:25 PM
Thread: Bandsaw electrics
by Elleff- Replies
- 5
- Views
- 1,803
Thanks Penguin Avery and Acco, Checked the...
Thanks Penguin Avery and Acco,
Checked the safety switch without any joy, Pulled out the start switch and blew it out with air and hey presto. All is now go!! I must admit I was surprised how much... -
26th July 2012, 04:59 PM
Thread: Bandsaw electrics
by Elleff- Replies
- 5
- Views
- 1,803
Bandsaw electrics
Hi All,
I have a Carbatec 19" Bandsaw which has been running quite OK. This morning I was checking blade tension, adjusting blade to perpendicular etc and vacuuming dust from nooks and crannies in... -
12th July 2012, 06:32 PM
Thread: Which router table
by Elleff- Replies
- 3
- Views
- 1,743
I have a spindle moulder but doubt that the drive...
I have a spindle moulder but doubt that the drive shaft will wind low enough to accept a chuck for 3/8" or 1/2" bits. I'm also thinking routers are a better way to go for smaller profiles
-
12th July 2012, 04:51 PM
Thread: Which router table
by Elleff- Replies
- 3
- Views
- 1,743
Which router table
Hi All,
I currently have an old Triton Router Table with a Makita 3601B. I am starting to do a bit more router work and have become disenchanted with this set up. Changing bits is a drama and... -
19th September 2010, 01:37 PM
Thread: Combination Jointer/thicknesser???
by Elleff- Replies
- 36
- Views
- 9,203
It's not as simple as buying a machine and going...
It's not as simple as buying a machine and going to work is it? The question of options, transport and setup are all difficult decisions. At the moment I am looking at picking up and transporting...
-
17th September 2010, 12:20 PM
Thread: Combination Jointer/thicknesser???
by Elleff- Replies
- 36
- Views
- 9,203
Thanks to all for your advice. I will certainly...
Thanks to all for your advice. I will certainly pay some attention to the static issue and if unsuccessful you will see my notice on the back of the daily rag! Back to the subject issue of this...
-
17th September 2010, 11:36 AM
Thread: Combination Jointer/thicknesser???
by Elleff- Replies
- 36
- Views
- 9,203
Morning all, Whilst we would all like to think...
Morning all,
Whilst we would all like to think we will not experience explosions in the workshop I would like to avoid this experience if possible. Am I right to assume that the wire inserted into... -
9th September 2010, 03:28 PM
Thread: Combination Jointer/thicknesser???
by Elleff- Replies
- 36
- Views
- 9,203
I suppose it's fair to say I have a whole lot of...
I suppose it's fair to say I have a whole lot of decisions to make as I'm setting up a new workshop. I do have a bandsaw and whilst it is only a 14" Carba Tec it seems to have done what I've asked of...
-
8th September 2010, 03:26 PM
Thread: Combination Jointer/thicknesser???
by Elleff- Replies
- 36
- Views
- 9,203
Thanks for your advice. I must admit I favoured...
Thanks for your advice. I must admit I favoured the separate machines but it's always good to get advice first from someone who has been there done that. I once made a decision without consulting my...
-
8th September 2010, 02:35 PM
Thread: Combination Jointer/thicknesser???
by Elleff- Replies
- 36
- Views
- 9,203
Combination Jointer/thicknesser???
Hi all,
I'm a new member on this forum and invite comment on my current plans.
I'm setting up a workshop and trading my triton for a table saw which will probably be carba tec. I also want to do...