Search:
Type: Posts; User: penguin
Search: Search took 0.00 seconds.
-
8th November 2014, 05:04 PM
Thread: Steel for making your own carbide tools?
by penguin- Replies
- 27
- Views
- 4,407
you can also buy stainless steel for make a...
you can also buy stainless steel for make a keyway form bolt suppliers in either metric or imperial in all different sizes and is in 300mm lengths
regards
penguin -
26th July 2012, 05:15 PM
Thread: Bandsaw electrics
by penguin- Replies
- 5
- Views
- 1,805
try holding in the door switch when pushing start...
try holding in the door switch when pushing start button and check for a lower door switch hope this may help
penguin -
2nd July 2012, 12:56 PM
Thread: Hammer bandsaw - bolt hole thread size?
by penguin- Replies
- 7
- Views
- 2,245
You will need to remove a bolt and get the...
You will need to remove a bolt and get the correct thread as there is fine and course metric threads one is pitch 1 and theother is 1.5 pitch for m 10 bolts there is different thead pitch for all...
-
13th November 2010, 07:46 PM
Thread: Gummy Roller Guides
by penguin- Replies
- 1
- Views
- 1,331
gummy rollers
I have had the same problem with some pine and took some cleaning and I have also read in the forum that if you put diesel on the blade and rollers it reduces build up but only a smear.Hopes this...
-
29th September 2010, 10:00 PM
Thread: Looking for info re jointer
by penguin- Replies
- 5
- Views
- 2,056
jointer info
If you have a Gasweld near you they look simlier might be of some help
penguin -
19th September 2010, 09:35 PM
Thread: Variable speed treadmill/Lathe Conversion
by penguin- Replies
- 6
- Views
- 4,694
vsd
I brought 2 1.5kw vsd's of a different brand of ebay and fitted them to a wood lathe and a linisher I was given from work that was going to be thrown out.They are both 2800rpm 3 phase motors and work...
-
22nd April 2010, 03:05 PM
Thread: Woodfast 10" Bandsaw
by penguin- Replies
- 13
- Views
- 3,645
Check out any car or truck tyre place close to...
Check out any car or truck tyre place close to you ,you might be able to get an old tube that is a bit smaller and stretch it on to the wheel .be nice to the dealer and you might get it for free
... -
6th October 2007, 03:53 PM
Thread: Bandsaw Butt Welder
by penguin- Replies
- 2
- Views
- 1,894
I do not know about butt welders but carbatec and...
I do not know about butt welders but carbatec and mjing tools have a tool for joining bandsaw blades hope this helps
penguin -
3rd October 2006, 06:48 PM
Thread: Different shape, for me.
by penguin- Replies
- 19
- Views
- 2,980
good job like the shape and finish penguin
good job like the shape and finish
penguin -
3rd October 2006, 06:37 PM
Thread: rosewood bowl
by penguin- Replies
- 9
- Views
- 1,588
Skew scalloped after turning making shape on...
Skew
scalloped after turning making shape on paper and cutting with mini hacksaw and then sanding up
Terry,Josh I have a piece of timber I routored out so I a flat base and back ,I use masking... -
2nd October 2006, 11:57 AM
Thread: rosewood bowl
by penguin- Replies
- 9
- Views
- 1,588
rosewood bowl
just finished this bowl out of rosewood 191 pieces 160 mm high and 240 round SHMBO likes it finished with eee and 2 coats shelawax enjoy if you like
penguin -
22nd September 2006, 12:04 PM
Thread: blade guides
by penguin- Replies
- 4
- Views
- 1,589
harry72 and china the shield are the covers that...
harry72 and china the shield are the covers that cover the rollers in the photo the left is steel and if you enlarge you will see small cuts in the sheild which lets in the dust and the right is a...
-
21st September 2006, 04:47 PM
Thread: blade guides
by penguin- Replies
- 4
- Views
- 1,589
blade guides
just a note to let you know if you have bearings for roller guides and they metal sheilds when they seize up replace with rubber sheilds as they spin a little slower but they will last a lot longer...
-
28th August 2006, 09:20 PM
Thread: segmented turning and press
by penguin- Replies
- 5
- Views
- 2,380
skew I use hose clamps to hold the rings together...
skew I use hose clamps to hold the rings together after gluing most times I have 2 small hose clamps together to get a larger size range and use the press to flatten the rings and then to build up...
-
28th August 2006, 09:15 PM
Thread: First Turning
by penguin- Replies
- 11
- Views
- 1,789
nice work we have all got to start somewhere ...
nice work we have all got to start somewhere
penguin -
28th August 2006, 10:53 AM
Thread: segmented turning and press
by penguin- Replies
- 5
- Views
- 2,380
segmented turning and press
this is my first postIved the site for awhile .I have picked up a lot of good ideas from all the posts that have submitted and the info has been of great asssitance so i am attaching some photos of...