Search:

G'day men, I've have just bought a Carbatec 13" Spiral Head Thicknesser and haven't opened yet cause I'm thinking to take it back and get the Dewalt 735. The Carbatec has spiral cutters and the...

Thank you for your reply. I went and saw Kim but he doesn’t sell any timber he even uses all his off cuts. I’ll contact Djarilmari and find out where they and have a chat with them. Thanks again. ...

Gentlemen, I'm travelling through the wheatbelt of WA and heading to Exmouth and would love to get my hands on some Gimlet and Salmon gum. I live in the Geelong area of Victoria and would like to get...

I'm after some metal shims for a dado stack. I have a set but they're 5/8 bore and I'm after a 30mm bore. I have a plastic set but they are on the way out. I've had a look on line but to no avail. ...

G'day Crowie, I bought one from Hare and Forbes in October last year. I sent them the measurement but the one they sent was too big. So I managed to put the old one back but it's a mongrel to install...

I'm in.

Bowed.
If it was cupped I think i'd dump it but being bowed I might have a better chance of saving it. I'm just not sure how to go about it.
Marty

Good morning, I have two pieces of camphor laurel which are both bowed. One is about 50cms and the other about 90cms long and about 40cms wide. What is the best way to straighten them. Any clues...

I'm in.

"I'm in"

I’m after some information please. My table saw is 50” on the right hand side and I’m cutting a hole in to take a router. What I would like to know is if it makes a difference which way the router...

Gentlemen,
I have a Metabo DH330 thicknesser about 5 years old and I would like to install spiral cutters as the replacement for the two cutters is about $77 from England. They normally last about 9...

I'm in.

I’m in.

I'm in.

G'day Gary would you send me the dimensions including weight so I can work out the postage cost.

Marty

Sent from my iPhone using Tapatalk

You're dead right Rob. I rang the place where I bought it and he said the same thing. Since my initial question i stripped it again. Loosened that locking ring you mentioned moved it a bit, I think...

I have a Harvey table saw which apart from one little problem is great. The lowering and raising of the blade has become quite difficult. I removed the top and gave it a clean out got as much sawdust...

Binary01 I read your interesting article about cleaning the worm gear on your Harvey table saw as I have a similar problem with mine, hard to rise and fall. What I would to know is did you put any...

Thanks for the replies. I had a look at the Bunnings site and all the blades were 12". Mine is a 10" blade.

Does anyone have any information on machining out saw blades holes. I have a table saw with 30mm arbor which reduces my choice on saw blades. I'm interested in the Freud blades but as far as I can...

Grahame the squares look great, but how much are they or will be?

Marty

G'day FV if you go to the Grizzly site (below) you should/maybe find the bandsaw which is the same as yours and can then download the manual.

Grizzly.com® -- Product Categories


Marty

Hello, I'm not much of a contributor to this forum, but I do subscribe to about 10 threads and read them every day and there's a lot of admiration of some very clever people out there.

A friend...

Firstly I'm not sure that this is the correct forum, but here goes anyway. I'm sure someone will put me on the correct track.

As you can see by my joining date I haven't joined into many...

We lived in East Warby for about 4 years when my father was working on the Upper Yarra dam and it was fantastic. We moved into a house after living with friends who were down Riversdale Road, which...

Steve,

Timbercon have them as per their web site http://www.timbecon.com.au/products/abrasive-paper-discs-386_0.aspx

Marty

John, I have just had my house relevelled and the builder used stirrups as per the photo and is a simple but effective method. I don't know if this will help you.

Marty

18755

I'm about to purchase my first woodworking piece of equipment and I was told to buy a dust extractor.

Have been looking around at the 2 - 3 hp units and on Friday found my way to the local...

When my late and great father in law was alive he loved working with his hands but being an academic he did find a bit frusting. Many a time when I visited him he had a bits if skin missing but he...

[QUOTE=inferno6688]


I am currently favouring the Hafco SB-10H, or the carbatec equivalent, which is the MJ2325B but its now got a 3HP motor i dunno if the model number is the same.
...

imdusty,

If you want to learn strine check this out http://www.koalanet.com.au/australian-slang.html and you may be able to understand the lingo a bit more beauta.

Marty

Phil, 370 watts is equal to 0.49617817 hp or roughly there abouts approximately.

Marty

Harry72, does the Freud fit all saws or is there only a few that it will go onto. I remember reading somewhere that it needs a long arbour do you know if that's correct.

Marty

Would someone tell me what the quill on a drill press does please and is it better for a small one or larger.

At the Waurn Ponds store this morning the Triton Router was $339 but the trouble was.............I wasn't alone.

......me too!!

The price you have stated, are they with the 20% off and would you post them.

Paddy

Just the fact that you won't be chipping the slag off and putting dents into the metal would be enough reason for getting a MIG. The only cleaning would be the splatter and you can get a...

I have a set of cane chairs which are in need of repair and re-varnishing (if that's what you do to them) and was wondering if anyone have the knowledge to re-vamp.

Well you blokes do insist on using PCs.

Have a look at http://cgi.ebay.com.au/LUFKIN-6M-TAPE-MEASURE-BRAND-NEW_W0QQitemZ4408332980QQcategoryZ20766QQcmdZViewItem it claims that it's both right and left. haven't seen it but might be a worth...

G'day aljenit,

Was there yesterday but didn't see him was too busy buying some trees so I can make some furniture in 20 years time it is an unusual place to sell those items. I've mostly seen home...

Try Geelong Machinery along Portarlington Road. Cash talks and about 2 months ago $1100.