Search:
Type: Posts; User: TTS_Brett
Search: Search took 0.00 seconds.
-
2nd September 2014, 11:09 AM
- Replies
- 46
- Views
- 7,217
Hello Fencefurniture The advice you have...
Hello Fencefurniture
The advice you have been given here is very good and in line with what we might also suggest
If the issue continues please give us a call at Festool or... -
1st July 2014, 10:08 AM
Thread: festool tool with no earth??
by TTS_Brett- Replies
- 12
- Views
- 2,185
Hi Bryan No I was not at the show in Sydney,...
Hi Bryan
No I was not at the show in Sydney, my colleagues tell me the event was great
We find shows good fun, catching up and talking to users of the product we all agree is the best part... -
30th June 2014, 10:14 AM
Thread: festool tool with no earth??
by TTS_Brett- Replies
- 12
- Views
- 2,185
Correct, the Kapex is double insulated and...
Correct, the Kapex is double insulated and therefore the earth is not connected
-
30th June 2014, 10:10 AM
Thread: ET2E sander repairs
by TTS_Brett- Replies
- 2
- Views
- 3,739
Hi Mark There are two ways to remove the...
Hi Mark
There are two ways to remove the eccentric bearing from the ET 2 E, the first requires the use of Festool special service tool designed specifically for the removal of ET and ETS... -
23rd September 2013, 10:09 AM
- Replies
- 2
- Views
- 1,527
Hello Denque When rotating the mitre angle on...
Hello Denque
When rotating the mitre angle on the Kapex there will be some resistance but you should not need to fight it
If you would like to please PM me your contact details, I will call... -
16th September 2013, 12:25 PM
Thread: Regreasing Protool gearbox
by TTS_Brett- Replies
- 5
- Views
- 2,368
Hello Andrew The greases used in the DRC and...
Hello Andrew
The greases used in the DRC and PDC range of cordless drills are listed below
UniSilikon L250 (White) for the 4 speed gear change ring
Signum SXT 2 (clear) for internal gears... -
12th September 2013, 03:15 PM
Thread: Festool, DIY workshop
by TTS_Brett- Replies
- 9
- Views
- 1,823
Would like to bump this back to the top I have...
Would like to bump this back to the top
I have been chatting to persons involved with this event and it looks like its going to be a good day
Check out Bruce's original post for details
... -
12th September 2013, 01:58 PM
Thread: TI15 Impact driver on 18v batteries
by TTS_Brett- Replies
- 2
- Views
- 1,082
Hello elanjacobs I have just noticed that you...
Hello elanjacobs
I have just noticed that you have not had a reply to your post :o I apologise for this
The 18 Volt batteries cannot be fitted to lower voltage tools, they are physically... -
29th July 2013, 10:42 AM
Thread: Brush replacement
by TTS_Brett- Replies
- 6
- Views
- 1,432
Festool Protool spare parts
Hello TheBerylBloke
Spare parts including carbon brushes are available for Festool and Protool products, these can be obtained during the the warranty period, there are no restrictions
... -
17th July 2013, 12:27 PM
Thread: Unexpected problem with TS55
by TTS_Brett- Replies
- 9
- Views
- 3,668
Hello 02zi3 We are very disappointed to hear...
Hello 02zi3
We are very disappointed to hear of your issue with the TS 55 especially after this being your first introduction to Festool products:(
We have been in contact with Northern... -
14th March 2013, 05:34 PM
Thread: Festool KAPEX 120 fails after incident
by TTS_Brett- Replies
- 10
- Views
- 3,744
Hello Denque I am glad to hear that your...
Hello Denque
I am glad to hear that your Kapex issue issolved
To put you mind further at ease I felt Ishould step forward and explain the ‘series of clicks’ you are hearing withinthe saw
... -
2nd April 2012, 10:30 AM
Thread: Festool parts.
by TTS_Brett- Replies
- 4
- Views
- 2,723
Hello Ratbag I am disappointed to read about...
Hello Ratbag
I am disappointed to read about your spare part experience, to us at TTS a spare part purchase is as important as a new tool purchase
The steel plate and cork supplied under...