Search:
Type: Posts; User: DBACT
Search: Search took 0.00 seconds.
-
8th November 2013, 02:47 PM
Thread: MIG Gas for a learner
by DBACT- Replies
- 3
- Views
- 906
MIG Gas for a learner
I purchased a Unimig KMN180 to teach myself MIG welding. What gas should I get? I'll be seam welding a car, making brackets and engine mounts, etc
-
25th February 2013, 02:34 PM
Thread: Barry Hull's - Self Locating Centre Punch
by DBACT- Replies
- 1
- Views
- 1,824
Barry Hull's - Self Locating Centre Punch
Anyone know where I can buy the Barry Hull's self lcating centre punches? All I have is Teebone knee pads and elbow guards. Distributor of the self locating centre punch and the emails and phone...
-
21st April 2008, 01:27 AM
Thread: Workshop storage/work space options
by DBACT- Replies
- 4
- Views
- 2,246
Workshop storage/work space options
I am looking to fit out a 6x9m shed soon to be built and want some workshop storage units. (... space for a car restoration and a comfortable man cave! :U)
What options are there?
1. At... -
24th February 2008, 02:19 PM
Thread: Attaching a trim piece
by DBACT- Replies
- 5
- Views
- 2,310
Update. I did not really need to be removeable as...
Update. I did not really need to be removeable as the oven could be slide out without removing the trim piece. I did however use a couple of heavy duty magnetic door closers and a few 10mm disc...
-
24th February 2008, 02:14 PM
Thread: Gas Heater flue
by DBACT- Replies
- 2
- Views
- 1,872
Gas Heater flue
I have a Brivis Buffalo 120 heater located in an underhouse area I would like to build into a utility room.
Can I add a extended flue to vent it to an outside wall? Is it possibly to box in the... -
18th November 2007, 12:21 AM
Thread: Attaching a trim piece
by DBACT- Replies
- 5
- Views
- 2,310
Attaching a trim piece
In the pic, I am fitting the trim around the oven. I'd appreciate some assistance with fastening the top marked A and middle B. Down the bottom is OK
It needs to be removable to service the oven.... -
18th September 2007, 12:20 AM
Thread: Blistering under glued vinyl
by DBACT- Replies
- 1
- Views
- 1,583
Blistering under glued vinyl
I glued a small sheet of vinyl using Kwik Grip to finish a section to left and above the stove top and there has been some bubbling/blistering, as per the pics. The trim piece is 670mm above the...
-
1st September 2007, 01:08 AM
Thread: Trimming vinyl wrap panel
by DBACT- Replies
- 3
- Views
- 2,030
Trimming vinyl wrap panel
The last trim panel (vinyl wrapped) and I got a bit lazy. It's not square. I will need to take off 2mm or so along a short edge. Can this be done?
I suspect that once I cut through the vinyl,... -
24th July 2007, 07:29 PM
Thread: Drilling vinyl wrap doors
by DBACT- Replies
- 5
- Views
- 3,109
Drilling vinyl wrap doors
I am drilling holes in vinyl wrap doors for handles. Before I tear up the vinyl and ruin a perfectly good door, is there any tips? Should I drill from front to back or vica versa? Would masking tape...
-
20th June 2007, 12:06 AM
Thread: overlay self-closing hinges
by DBACT- Replies
- 7
- Views
- 2,531
Also give Lincoln Sentry 51 lorn st queanbeyan a...
Also give Lincoln Sentry 51 lorn st queanbeyan a try
-
14th June 2007, 11:36 PM
Thread: Shower Hob
by DBACT- Replies
- 4
- Views
- 4,055
Do you specifically want a hob? I used angle,...
Do you specifically want a hob? I used angle, waterproofed it and then tiled. The shower was fitted just inside the angle.
-
14th June 2007, 03:06 PM
Thread: Left vs right hinges
by DBACT- Replies
- 7
- Views
- 3,014
Left vs right hinges
I'll be ordering some doors predrilled for hinges soon. so that there is no confusion, what is a left hinged door? Is it from the outside or inside? ie. if the hinge is on the left hand side of the...
-
14th June 2007, 03:01 PM
Thread: overlay self-closing hinges
by DBACT- Replies
- 7
- Views
- 2,531
You may wish to give Duratech a call at fyshwick....
You may wish to give Duratech a call at fyshwick. They supplied some Blum hinges at a reasonable price recently when I ordered some doors. Much cheaper than hettich I purchased at magnetmart. I do...