Search:
Type: Posts; User: Dwano
Search: Search took 0.00 seconds.
-
19th April 2016, 05:05 PM
Thread: Radial saw or combination slide saw.
by Dwano- Replies
- 13
- Views
- 1,352
Thankyou for your advice. I was sure the RAS...
Thankyou for your advice. I was sure the RAS could be an accurate machine but when you have no info of how and only trial and error this takes a lot of time. I will go to this forum and see what I...
-
18th April 2016, 11:10 PM
Thread: Radial saw or combination slide saw.
by Dwano- Replies
- 13
- Views
- 1,352
Many thanks. I have printed the DeWalt manual....
Many thanks. I have printed the DeWalt manual. My saw is a 12 inch but the instructions should be pretty much the same for both. Again Thanks.
-
18th April 2016, 10:01 PM
Thread: Radial saw or combination slide saw.
by Dwano- Replies
- 13
- Views
- 1,352
I have just spent some time looking for an online...
I have just spent some time looking for an online version of the manual but to no avail. Do you have any clues where on the internet it might be found? I will spend some more time googling to try and...
-
18th April 2016, 09:05 PM
Thread: Radial saw or combination slide saw.
by Dwano- Replies
- 13
- Views
- 1,352
Many thanks malb. I do not have the manual for...
Many thanks malb. I do not have the manual for this saw as I aquired it when it was being thrown away. It had been left out in the weather for some time and it took a bit to clean the rust off and...
-
18th April 2016, 07:18 PM
Thread: Radial saw or combination slide saw.
by Dwano- Replies
- 13
- Views
- 1,352
Hi BobL. Thanks for your reply. I have tried to...
Hi BobL. Thanks for your reply. I have tried to adjust the work surface as there appears to be no adjustment for the blade tilt except when tilting for angle cuts. I have a TATRY Italian made saw...
-
18th April 2016, 02:31 PM
Thread: Radial saw or combination slide saw.
by Dwano- Replies
- 13
- Views
- 1,352
Radial saw or combination slide saw.
Hi all. I am not sure if I have found the correct area but I was wanting to get some feed back as to which machine people are using and why. I am trying to decide which would be better and more...
-
24th September 2013, 09:40 PM
Thread: Samco combination machine.
by Dwano- Replies
- 3
- Views
- 4,482
Re Samco.
Hi. I have a Samco combination under and over. Mine is a 300mm machine. I bought this a while ago and have found it a good solid and robust machine. Yes these were made by SCM in Italy. Mine is no...
-
21st June 2013, 10:43 AM
Thread: Samco FS 300 combo planer / thicknesser
by Dwano- Replies
- 5
- Views
- 4,615
Re Samco.
Thanks for your input. I am not able to put up a pic just yet but I will do this. The problem is I do not have a manual for this machine so everything is trial and error. The blades are at the...
-
20th June 2013, 09:50 AM
Thread: Samco FS 300 combo planer / thicknesser
by Dwano- Replies
- 5
- Views
- 4,615
Samco FS 300 combo planer / thicknesser
Hello all.
I am hoping that some kind person might have some information for the set up of a Samco FS 300 planer / thicknesser. I purchased this machine for use in my shed but unfortunately there... -
31st March 2013, 09:59 PM
Thread: Looking for a Table Saw
by Dwano- Replies
- 10
- Views
- 3,073
tolex 10" withsliding table.
Hi there.
I am relatively new to this forum. I stumbled across your post and was interested as I have a Toolex 10" with the sliding table that is now surplus to my needs. I bought a panel saw. I... -
28th January 2013, 08:28 PM
Thread: Which Planer/ Thicknesser
by Dwano- Replies
- 3
- Views
- 2,286
Yes I have two dust extractors, well actually...
Yes I have two dust extractors, well actually three. One attached to the panel saw. One for the planer/thicknesser. And one attached on the stroke sander. As yet I have not sorted out the best way to...
-
28th January 2013, 08:22 PM
Thread: Hunter forumites gtg
by Dwano- Replies
- 52
- Views
- 6,342
This would be nice to meet some of the Hunter...
This would be nice to meet some of the Hunter woodworkers, however I have already been booked to be away. Hopefully next time.
Cheers
Dwayne -
27th January 2013, 08:26 PM
Thread: Which Planer/ Thicknesser
by Dwano- Replies
- 3
- Views
- 2,286
Which Planer/ Thicknesser
Hello all. I am in a quandry as to which combo machine I should actually look at. I have been using a little 10" Hafco under and over, however this machine is alright but lacks the accuracy and...
-
G'Day
Hello All. I have just joined this forum to see who is near by and to find out hopefully good information and advice. I dabble with making some long awaited furniture that my wife has waited, very...