Search:

Yes, It's Unistrut hardware.
Browse Unistrut Trolley-Assemblies

You can buy it from lots of different places.

Yes it is fine. Play with it as much as you want but be aware that the terminals will be live. Unplug it and wait for the screen to go dark before touching any terminals.

The cast iron surface on a contractors saw is not that big so 1.5mm is significant IMO. I would not be happy and would be looking at a return/replacement as it is new.

If you're generating enough dust to damage hearing aids I think the impact on your lungs is of greater concern.
Solve the problem not the symptom.

You can't attach images to a pm. URL only

Hi delbs,
The Artisan one you linked is way too expensive for what it is. A treadmill motor may not be suitable as they are usually DC which would mean wrangling the speed controller into an...

I just watched a heap of them (I'm supposed to be working). Loved it.
Pity I was a couple of days late for the 5k follower giveaway.
I was impressed with the shipping box testing. Very thorough.

Ammo boxes 25pdr 1943. | eBay

I'm in

I was just about to tell you to drop the rated freq to 50 Hz but I see you've sorted it out. Is this going on the lathe?

Its a mortice chisel for cutting 3/8" mortices.
How to cut a THROUGH MORTICE AND TENON by HAND - YouTube
Jump to 10:40 to see him cutting the mortice

Is it one of these Paul?
Interwood Super-Square % 305mm, Large, Woodwork- Interwood Tools

I'm in

Just keep using it on the 10 amp GPO. The worst that will happen is you will blow the fuse or trip the circuit breaker.

You can't buy Office 365. You pay your money, they give you a download link and a code. Even if you get a box it just has download instructions and a code in.
Pretty sure Office 2019 is the same but...

You're not buying software. Your just purchasing a code. Probably cracked. You will download the software from Microsoft and put in the code. It will probably work. I wouldn't count on support...

Steps 1-4 are to raise the grain of the wood and prevent the finished item from having a fuzzy feel.
If you use a water based dye then a water based finish will leech the dye from the wood....

That would be ubeaut. I'm sure Neil will be along soon.

78.3mm, 102nn and 11.98mm so no go. You could use the jigs that don't have their own support bars but not the planer blade jig.

I'll grab it Andy. Will give you a ring later

Measure the Saber leg spacing and I will check it against the Tormek.

He's in, I think, West Virginia so we may not be of much help.

Narva make good stuff. I suspect the bad revue was an installation error rather than a malfunction. I had a look on the Narva site and while it's not plug and play it is reasonably easy to install....

I just weighed my, I think type 11 Stanley. 2517g and that is with a beefier iron and cap iron from a long ago group buy.

Nice write up :2tsup: You say it's much heavier than a vintage plane (I'm asssuming Stanley) Can you give me a weight? I've got a 5 1/2 here that I love using and I'm curious about the weight...

One thing I will say, try and avoid sticky outey bits. I just have a carriage bolt with a wing nut to provide clamping pressure and if I'm stitching a larger item there is a lot of spare thread...

Is that Sheffield Tassy or Sheffield England?

I think the fairies forgot to connect the VFD. It's hard to get hold of a competent fairy these days.
What timber are you thinking of for the lectern? And will it involve steam bending? And can we...

Yep, agree with Bob. If you stop suddenly that's 646kg of energy stored in that load. (I know it's not 646kg. It's the weight x speed x decelleration x friction co-efficient x wind speed x phase of...

If only you had a lathe to turn those....pillars.

It's all sorted now. The jig arrived (thanks Pat and Chris) and I spent half an hour or so getting all three blades perfectly flat and shaving sharp. Leaves a beautiful clean surface finish now....

Because TF paid 190 million dollars for the company. Thats nearly $2M per employee. I don't know about you but even checking down the back of the couch I can't scratch up $2M.
Although I might go...

Sorry, I didn't state that clearly enough. Connect the active and neutral to R & T. It doesn't matter which way around. Technically they are both active terminals.

R & T on the Powtran.

I'm in

Admin only. Be nice to a mod or our benevolent dictator himself.
I'm sure one will be along soon to help you out.

Incra Jig and Fence Combination | eBay

I can bend wood with my mind. Especially after I've just resawed it. I've learnt that if you say "Don't you bend you b&£$%!d, don't you bloody bend on me" it will bend about 90% of the time.
I will...

Probably closed their eyes while typing the reply.

I used to have one that looked exactly the same but was set up as a 4 inch post thicknesser. Had a 3 blade thicknesser head but no power feed. You had to push it through manually. I don't recall if...

It's just a Kreg rip off and he got it all for free so don't rely to heavily on his assessment. Personally I'd stick with the Kreg (I have a K3) but I have no idea what the rip off is worth. It might...

I haven't had a problem with rust and I have a large leather tool roll with around 20 chisels in. It is quite dry where I live though and I don't have a problem with rust on any surface tbh.

Thanks Pat, I'm sorry you don't get to move closer to Western Sydney.

I actually have a NATA certified calibration tape measure. You can buy the calibrated tapes for not a lot of money but mine is a 30m one that has been sent to a NATA lab (not by me) for verification....

That would be excellent if you could Chris. I'll have to do a trip to Camden soon so we can go via there.

Thanks J1T. Ill give it a little time to see if anyone local has one and then I'll get in touch. :2tsup: I can't remember who I sold mine to.

Surely you want to move closer to Western Sydney Pat. If you could move in the next couple of weeks that would be good.

I initially thought I could do that but they are sharpened at 40°. Can't get my table saw to 50°. I'll do it at 45° and put on a secondary bevel if I have to but thought I would try for a jig first....

Does anyone in Western Sydney have the Tormek Planer blade jig I could borrow. I had one but I sold it when I sold my old jointer.
I've recently picked up a little Paul Call jointer that is now...

I'll take it Andy. Will give you a call.