Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
Thread: Chuck Lube
-
4th April 2011, 10:25 PM #1
Chuck Lube
I am looking at the way I lube/maintain my chucks. I live in an area where brown mould happens overnight. I have been advised that the RP7 type sprays are not ideal and that silicone should not be used near wood. So what is recommended? INOX has been suggested. Any views?
Michael
Wood Butcher
-
4th April 2011 10:25 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
4th April 2011, 10:41 PM #2Retired
- Join Date
- May 1999
- Location
- Tooradin,Victoria,Australia
- Age
- 73
- Posts
- 11,918
Inox is what I would use.
RP7 etc dry out.
-
4th April 2011, 11:09 PM #3
The Chuck.
Hi Grommett,
Personally I'm not into Liquid "Lubes". I use Graphite Powder, $6.
So I would leave the Chuck in Petrol over night, let it dry & then squirt the G / P in.
I use the Older Black Nova's & I can pull them to pieces, say twice a year, give them a good wash with petrol, then blow dry with the air, & apply the Powder.
It's as if they had bearings in them.Regards,
issatree.
Have Lathe, Wood Travel.
-
5th April 2011, 09:28 AM #4
I use Lanotec (sp) but if you put too much on in cold weather, it goes a bit hard/sticky.
Cliff.
If you find a post of mine that is missing a pic that you'd like to see, let me know & I'll see if I can find a copy.
-
5th April 2011, 07:15 PM #5
I'm with on this one. Inox is great all round product for the workshop.
Russell (aka Mulgabill)
"It is as it is"
-
5th April 2011, 07:31 PM #6Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
Having tried a range of anti-rust products, Ferro-pak G15 stands out as the longest lasting treatment.
Cheers, Ern
-
5th April 2011, 07:49 PM #7
Inox for me does not attract dust like others.
Jim Carroll
One Good Turn Deserves Another. CWS, Vicmarc, Robert Sorby, Woodcut, Tormek, Woodfast
Are you a registered member? Why not? click here to register. It's free and only takes 37 seconds!
-
5th April 2011, 08:08 PM #8Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
G15 doesn't either Jim.
Any case, bottom line is whatever you use, wipe the chuck clean after a session at the lathe and apply the goo. And keep a watchful eye.
If you're green turning, whack on some goo before you start as well and clean up immediately afterwards.Cheers, Ern
-
5th April 2011, 09:59 PM #9
Green turning, love it but I rust as I do it, and I cannot afford to rust out just yet. Ferro- pak is new to me, found where? INOX is lanolin based? If so I like it immediately.
Michael
Wood Butcher
-
5th April 2011, 10:22 PM #10
Lanox is, not sure about Inox, it may be based on fish oil but I am not sure.
Have a look here & see what you can find.
Inox-MX3
Lanotec is based on Lanolin.
www.lanotec.com.auCliff.
If you find a post of mine that is missing a pic that you'd like to see, let me know & I'll see if I can find a copy.
-
5th April 2011, 10:48 PM #11
Oh well its kosher.
Michael
Wood Butcher
-
6th April 2011, 07:33 AM #12Hewer of wood
- Join Date
- Jan 2002
- Location
- Melbourne, Aus.
- Age
- 71
- Posts
- 12,746
G15 you can get from Jim Davey; also Chris Vesper IIRC. Ingredients not listed on the product, not even the fat or sugar content.
It's a spray can so can't be posted.Cheers, Ern
-
6th April 2011, 05:57 PM #13Lanox is, not sure about Inox, it may be based on fish oil but I am not sure.
Have a look here & see what you can find.
Inox-MX3
Hmm when their site talks about Inox they play their cards close to the chest. Its closely kept recipe.
But for me I go for the dry lubes and to date in Sydney I have had not a lot to do with maintenance on my chucks, other than a blow out with the air from time to time.Inspiration exists, but it has to find you working. — Pablo Picasso
Similar Threads
-
Do you use lube?
By comgreserv in forum SMALL TIMBER MILLINGReplies: 13Last Post: 4th October 2010, 01:32 AM -
MS 660 Chain Lube, HOW MUCH??
By Les Caddaye in forum SMALL TIMBER MILLINGReplies: 28Last Post: 6th December 2009, 09:51 AM -
Dry Lube
By Woody60 in forum WOODWORK - GENERALReplies: 2Last Post: 13th May 2009, 03:13 PM -
pully lube ?
By JDarvall in forum HAND TOOLS - UNPOWEREDReplies: 2Last Post: 27th May 2005, 01:49 AM -
Wool Lube
By Marty Lott in forum FINISHINGReplies: 0Last Post: 9th January 2001, 09:43 PM