Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 14 of 14
Thread: Oak platter
-
12th April 2012, 10:30 PM #1
Oak platter
I finished yesterday an oak platter, which is made out of leftover pieces of an old table top, had available for that a circular oak ring and a circular piece of oak.
The difficult trick was to provide a good fit of this circular ring and the other circular disc.
In my opinion not so a bad solution for using scraps of wood.
Better than throwing it into the fireplace
The platter is 325 mm in diameter, and is finished with two layers of water based acrylic laquer.
Cheers, Ad
-
12th April 2012 10:30 PM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
13th April 2012, 05:46 AM #2
Woodturners, the ultimate recyclers. Defiantly too good to of been burnt.
Good result, is SWMBO pleased with her new platter?Dragonfly
No-one suspects the dragonfly!
-
13th April 2012, 07:43 AM #3
-
13th April 2012, 07:47 AM #4
-
13th April 2012, 08:31 AM #5
Ad well done like the look of the two grain directions.
-
13th April 2012, 09:16 AM #6
Nice job Ad, always good to save wood. When I join two pieces like that, I make the joint at a small angle, about 4 degrees. Much easier than joining at 90 degrees. I think with that platter, I would make the grain parallel so that wood movement in both pieces would not fight.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
13th April 2012, 09:55 AM #7Skwair2rownd
- Join Date
- Nov 2007
- Location
- Dundowran Beach
- Age
- 76
- Posts
- 19,922
-
13th April 2012, 05:44 PM #8GOLD MEMBER
- Join Date
- Jun 2006
- Location
- Burwood NSW
- Age
- 82
- Posts
- 1,247
Nice save Ad
Jim, please explain why it is easier to join at 4 degrees than a rightangle.
Ted
-
13th April 2012, 06:15 PM #9
-
13th April 2012, 08:58 PM #10
Ted, imagine the platter sitting on a table. If the joint is at 90 degrees, the joint would be vertical, or at 90 degrees to the table. In this case, the two pieces would have to be absolutely exact to make a good joint. Now, by making the joint about 4 degrees off, or at 86 degrees to the table, there is a little tolerance in the diameter of the two halves.
Hope that explains what I was talking about.
JimSometimes in the daily challenges that life gives us, we miss what is really important...
-
14th April 2012, 04:47 PM #11GOLD MEMBER
- Join Date
- Jun 2006
- Location
- Burwood NSW
- Age
- 82
- Posts
- 1,247
Thanks Jim
Ted
-
14th April 2012, 11:26 PM #12
I reckon Ad you got the close tolerance fit perfect. But then I shouldn't be surprized, remembering the tolerances you made on the headstock bearings on your lathe.
... and nice platters to boot.Inspiration exists, but it has to find you working. — Pablo Picasso
-
14th April 2012, 11:31 PM #13Cliff.
If you find a post of mine that is missing a pic that you'd like to see, let me know & I'll see if I can find a copy.
-
18th April 2012, 11:00 PM #14
Platter looks nice
Similar Threads
-
A platter with fault!!!!
By vk4 in forum WOODTURNING - GENERALReplies: 22Last Post: 10th October 2011, 10:43 PM -
Platter
By Ad de Crom in forum WOODTURNING - GENERALReplies: 19Last Post: 24th March 2011, 10:10 PM -
The platter
By powderpost in forum WOODTURNING - GENERALReplies: 22Last Post: 2nd June 2009, 07:37 PM -
a Platter ???
By nine fingers in forum WOODTURNING - GENERALReplies: 20Last Post: 6th April 2009, 03:50 PM -
New platter
By powderpost in forum WOODTURNING - GENERALReplies: 18Last Post: 17th January 2009, 10:25 PM