Thanks: 0
Likes: 0
Needs Pictures: 0
Picture(s) thanks: 0
Results 1 to 13 of 13
Thread: Just a bit Wonky.....
-
7th August 2007, 01:52 AM #1
Just a bit Wonky.....
I have this roughed out cherry bowl, that dried really wonky, totally out of round, and to add to the troubles, the tenon on the base of the bowl cracked away from the base
Honestly, I should have put it in the "Interesting Firewood" pile, but, for some reason, I kept on trying to save this one.......
............I did the outside to a semblance of smooth between centers, and then cut a new tenon on it, and flipped it around to do the inside......
Attachment 52442
boy was this thing out of whack......
Attachment 52443 Attachment 52444
I'd say the balance is out a tad on this one
I got it done, with the help of a steady hand (lots of deep breathing) and nice sharp tools.........
Attachment 52445 Attachment 52446
Since the pics were taken I've turned off the bottom and I've started to spray this one with clear lacquer, I think there is enough going on here.
Thinnest point at the rim is somewhere around 1/16", the base is just under 1/4".
I'll post pics when it is done.
next time I get one like this it IS going in the burn pile, MAN I spent a LOT of time on this one.....It's a Family thing.....
-
7th August 2007 01:52 AM # ADSGoogle Adsense Advertisement
- Join Date
- Always
- Location
- Advertising world
- Age
- 2010
- Posts
- Many
-
7th August 2007, 02:09 AM #2
-
7th August 2007, 02:23 AM #3
Well this is not the same "Cherry" that you are used to, it is actually Sakura, a bit different, but yeah, it does crack!
Cheers!It's a Family thing.....
-
7th August 2007, 07:13 AM #4
Congratulations for your perseverance, Stu. I tried a stunt like that once. I found about half of the pieces, but the rest will have to await a complete cleanout of the shed.
JoeOf course truth is stranger than fiction.
Fiction has to make sense. - Mark Twain
-
7th August 2007, 09:03 AM #5
Excellent work, Stu. Nice post and dramatic pictures of timber instability during the drying process - a problem associated with working unseasoned timber I guess. It's one of the reasons that I have been playing with a few segmented pieces.
Your posts are always nicely presented with WIP pics etc and are most informative - always something to learn. Quite fascinating to see how thin you have managed to turn this one - albeit with some investment of time. I've seen a few posts here where they talk about getting bowls so thin they are translucent.
Does the timber ever tend to distort again, even after seasoning?
Regards. WayneDon't Just Do It.... Do It HardenFast!!
Regards - Wayne
-
7th August 2007, 09:38 AM #6
Good on Stu.
I see you still have that 'blatant advertising' stuck on your lathe.Cliff.
If you find a post of mine that is missing a pic that you'd like to see, let me know & I'll see if I can find a copy.
-
7th August 2007, 11:18 AM #7
Exceptional save, Stu. Good on ya!
Al
Some minds are like concrete thoroughly mixed up and permanently set.
-
7th August 2007, 12:11 PM #8
Wayne, thatnks.
Yeah, the wood will often continue to move when it gets this thin.
Cliff, think I'll get banned here tooIt's a Family thing.....
-
7th August 2007, 12:21 PM #9
-
7th August 2007, 05:26 PM #10
Nice one Stu.
I had a Joe Greiner experience in trying to save something way too distorted - got thinner and thinner, then eventually thin air!
I too vowed that the next one would join the firewood pile.
1/16th - thats a mite fine!Cheers,
Andy
"There's more wisdom gained in listening than in speaking"
-
7th August 2007, 11:11 PM #11
Thanks Andy.
Here it is with a few coats of rattle can lacquer.......
Attachment 52531
Needs to dry a while and then I'll do the triple buffing!
Attachment 52532
And it's finishing mate, a Ginko HF...........
Attachment 52533
yep..............another REALLY crappy piece of wood, too soft, hard to turn, hard to sand...... REALLY good for the burn pile this stuff is......
Cheers!It's a Family thing.....
-
7th August 2007, 11:45 PM #12
Still, 'tis an interesting shape....
Will that rattle can lacquer stay glossy or does it dull down to satin?
(I'm not a big fan of glossy but is seems to sell well)Cliff.
If you find a post of mine that is missing a pic that you'd like to see, let me know & I'll see if I can find a copy.
-
8th August 2007, 12:47 AM #13
This is the glossy stuff, so yeah.
I'll give it a few days, maybe even a week or so to out gas, and harden, then I'll go through the Beal buffing system, brown, white and wax, comes out super smooth.
For me it really depends, some things just look so nice with a super smooth glossy finish, this particular wood has a TON of chatoyance in the wood, so the smooth glossy finish shows that off, but I do hear you on the glossy stuff, can be done too much.
Cheers!It's a Family thing.....
Similar Threads
-
Stuck router bit.
By CT in forum ROUTING FORUMReplies: 18Last Post: 28th December 2008, 09:59 PM -
Help! my lock mitre router bit is trying to kill me
By joseph84 in forum WOODWORK - GENERALReplies: 23Last Post: 23rd August 2006, 05:11 PM -
where to get drill bit holder?
By inferno6688 in forum HAND TOOLS - POWEREDReplies: 3Last Post: 15th August 2006, 08:58 PM -
Veritas Router Bit Jack
By ddevida in forum ROUTING FORUMReplies: 2Last Post: 20th April 2006, 11:05 AM -
Drawer Locking Bit
By boxers in forum ROUTING FORUMReplies: 6Last Post: 16th April 2006, 08:59 PM