Search:

Tag: 0.25mm

Search: Search took 0.00 seconds.

  1. Only in an imperfect world would we be without vice.

    Started by Michael G, 22nd January 2014 07:55 PM
    2 Pages •
    1 2
    0.25mm, angle, annoyance, blunt, bottomed, clearance, cost, cutter, experience, fixed, freight, glacern, imperfect, jaw, kurt, liking, lock, managed, michael, model, moved, nice, set, solid, style, va-4, vertex, vice, weekend, world
    • Replies: 16
    • Views: 3,051
    Last Post: 24th January 2014 06:54 AM
    by Michael G  Go to last post

    Forum:
    METALWORK FORUM

  2. Do you bother to correct snipe

    Started by Mr Big, 10th January 2014 09:13 AM
    0.25mm, bother, calipers, correct, cure, deep, dip, final, finish, fix, forum, impact, iphone, lot, measured, planer, posts, provide, question, snipe, tapatalk
    • Replies: 7
    • Views: 2,747
    Last Post: 14th January 2014 02:14 PM
    by chambezio  Go to last post

    Forum:
    GENERAL & SMALL MACHINERY

  3. Aligning the blade on a table saw

    Started by Dengue, 9th August 2011 06:54 PM
    0.25mm, 10inch, 180deg, 270deg, acceptable, advise, aligning, alignment, blade, carbatec, deg, dial, finally, flat, gauge, indicator, mark, mitre, months, movement, operation, pointer, reading, rechecked, sitting, slot, table, teeth, thou, tsc-10hb
    • Replies: 2
    • Views: 1,779
    Last Post: 9th August 2011 07:38 PM
    by Dengue  Go to last post

    Forum:
    TABLE SAWS & COMBINATIONS

  4. Filling a complex surface

    Started by Arron, 29th June 2011 11:23 AM
    0.25mm, arron, banding, cheers, colours, complex, dry, elements, filler, filling, gaps, guess, ideas, impact, leave, level, loose, main, maximum, muddies, perfect, red, sand, species, surface, timber, top, veneer, white, wipe
    • Replies: 11
    • Views: 1,769
    Last Post: 17th July 2011 11:13 PM
    by Arron  Go to last post

    Forum:
    FINISHING

  5. Slimming Mill Gib

    Started by Stustoys, 2nd March 2011 05:05 PM
    0.25mm, 28mm, 520mm, axis, bayswater, brass, cardboard, gib, matter, melbourne, mill, piece, plastic, roughly, s/s, sells, shim, slimming, steel, stuart
    • Replies: 14
    • Views: 1,724
    Last Post: 5th March 2011 09:15 PM
    by Stustoys  Go to last post

    Forum:
    METALWORK FORUM

  6. New Table Saw

    Started by DJ’s Timber, 14th October 2008 10:56 AM
    2 Pages •
    1 2
    0.25mm, 1.5mm, 2tsup, 85869, 85870, 85871, 85872, 85873, 85874, 85875, 85876, adjust, approximately, assembling, cool, dead, easy, edge, fine, gauge, hours, kicked, measure, mitre, pick, set-up, slots, spent, table, unload
    • Replies: 17
    • Views: 4,320
    Last Post: 15th November 2008 11:05 PM
    by MatMann  Go to last post

    Forum:
    TABLE SAWS & COMBINATIONS

  7. Problem with GMC thicknesser

    Started by EMistral, 29th November 2007 08:50 PM
    2 Pages •
    1 2
    0.25mm, advance, annoying, blade, change, checked, day, eric, forever, gmc, gum, idea, minutes, net, pass, past, prior, problem, remove, resume, roughly, shaving, solution, spotted, taking, thick, thickness, thicknesser, times, woodworking
    • Replies: 18
    • Views: 3,148
    Last Post: 1st December 2007 09:28 AM
    by SAISAY  Go to last post

    Forum:
    WOODWORK - GENERAL

  8. Tinted varnish repair

    Started by Sebastiaan56, 20th October 2007 06:10 AM
    0.25mm, added, change, character, colour, distress, dopey, dyed, expect, flakes, friend, guitar, hand, leaving, lot, peels, raw, repair, repairing, sanding, send, shellac, stuck, suggestion, thick, timber, tint, tinted, underneath, varnish
    • Replies: 4
    • Views: 2,256
    Last Post: 20th October 2007 03:48 PM
    by astrid  Go to last post

    Forum:
    FINISHING

  9. 4 down 29 to go

    Started by Shedhand, 29th December 2006 11:58 PM
    0.25mm, 2tsup, 42mm, blade, cry3, curlys, cut, hope, knob, match, matched, oak, patina, perfectly, purists, purty, reason, repair, sanded, sanding, series, set, spare, stanley, tas, tote, type, user, wide, wood
    • Replies: 8
    • Views: 1,486
    Last Post: 31st December 2006 05:46 PM
    by Shedhand  Go to last post

    Forum:
    HAND TOOLS - UNPOWERED

  10. Too thick... :(

    Started by Skew ChiDAMN!!, 19th October 2006 09:59 PM
    0.25mm, 0.5mm, 1.5mm, 1mm, belt-sander/linisher, cutting, damned, diagonals, eek, effort, equally, fine, flying, gonna, grab, handle, imho, laminations, laterals, pittosperum, purpleheart, rolleyes, sand, sanding, tend, thick, tips, veneers, wedges, [sigh]
    • Replies: 14
    • Views: 2,026
    Last Post: 20th October 2006 11:44 PM
    by lubbing5cherubs  Go to last post

    Forum:
    WOODTURNING - PEN TURNING

Results 1 to 10 of 11